background image

 

 

12 

DIP Switch #3–#4: Auto close time of the gate opener 
DIP Switch #3: ON

 – 30 Seconds 

OFF

 – 0 

DIP Switch #4: ON

 – 60 Seconds 

OFF

 – 0 

NOTE: The auto close function would be disabled if both dip switches are turned to off (factory 
default setting). 

 
 

 
DIP Switch #5: Left/Right open 
ON

 – Left open (factory default setting).   

OFF

 – Right open. Turn switch OFF to change the opening direction easy if necessary.   

 

 

How to Program or Erase the Remote 

 

The remote MUST be programed to the opener BEFORE OPERATING. Please follow the steps to 
program the remote. 

 

Activate the opener only when gate is in full view, free of obstruction and properly adjusted. No 
one should enter or leave gate area while gate is in motion. DO NOT ALLOW CHILDREN to 
operate push button or remote. DO NOT ALLOW CHILDREN TO PLAY NEAR THE GATE. 

 

If you purchase additional remote controls, the gate opener must be programmed to accept the 
new remote code. 

 

If you lose one of any remote control, please erase and reprogram all other remote controls to 
have a new code for safety. 

Program the remote 

Press and release the learn button, the 

REM

 

LED

  light will be  on, then press  the key in the 

remote twice  in 2 seconds, the 

REM LED

  light 

will  flash for 4 seconds. Now the remote has 
been programmed successfully. 

Erase all the remote codes 

Press and hold the learn button until the 

REM

 

LED

 light is off. Now all remote codes have been erased. 

 

NOTE:

 

Max. 8 remotes can be programmed for the opener. An External Receiver (optional) allows up to 

250pcs remotes to be programmed for the opener. TOPENS ERM12 Universal External Receiver is 
available at TOPENS Store.   

 

TOPENS ERM12 Universal External Receiver is also compatible with other brand swing gate 
opener, sliding gate opener and garage door opener. 
 

E.g.                   Auto close time of the gate operator is 30+60=90 seconds. 

Содержание RK2600


















Отзывы: