manualshive.com logo in svg

Topcon LN-100, Инструкция по эксплуатации

Поделиться
Скачать
Topcon LN-100 Скачать руководство пользователя страница 26

23

7. CHECK

1. Set the instrument at instrument point 1.

2. Measure the target set at measurement point a to record the coordinates.

Because the target is re-measured at measurement point a after shifting to measurement point b, 
the position should be marked (positioning accuracy is approximately ±1mm).

3. Set the target at measurement point b.

4. Measure the target set at measurement point b to record the coordinates.

5. Set up the instrument at instrument point 2.

6. Measure the target set at measurement point b to record the coordinates.

7. Set the target at measurement point a.

Return to the measurement position shown in 2. above.

8. Measure the target set at measurement point a to record the coordinates.

µí

µí

²°í

Éîóôòõíåîô

ðïéîô ²

Éîóôòõíåîô

ðïéîô ±

Íåáóõòåíåîô ðïéîô â

 Íåáóõòåíåîô ðïéîô á

µí

µí

²°í

Éîóôòõíåîô

ðïéîô ²

Éîóôòõíåîô

ðïéîô ±

Íåáóõòåíåîô ðïéîô â

Íåáóõòåíåîô ðïéîô á

µí

µí

²°í

Éîóôòõíåîô

ðïéîô ²

Éîóôòõíåîô

ðïéîô ±

Íåáóõòåíåîô ðïéîô â

Íåáóõòåíåîô ðïéîô á

µí

µí

²°í

Éîóôòõíåîô

ðïéîô ²

Éîóôòõíåîô

ðïéîô ±

Íåáóõòåíåîô ðïéîô â

Íåáóõòåíåîô ðïéîô á

Содержание LN-100






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды