manualshive.com logo in svg

Topcon LN-100, Инструкция по эксплуатации

Поделиться
Скачать
Topcon LN-100 Скачать руководство пользователя страница 21

18

5. PREPARATION

Auto leveling

• By performing auto leveling, the center of the instrument is automatically leveled within the range 

of ±30". After that, if the inclination of the main unit exceeds the range of inclination 
compensation (±6'), the red LED will light up. In this case, auto leveling will not automatically 
start. Perform auto leveling again.

PROCEDURE

1. Press {Auto leveling switch} while auto leveling is stopped.

The auto leveling LED starts blinking in green and auto leveling starts. After completing auto 
leveling, the LED lights up in green.

• If a foreign object gets caught in the auto leveling section, hold down {Auto leveling switch}.

If the leveling screw is extended, remove the foreign object, and restart auto leveling.
The following describes how to press {Auto leveling switch} and its relationship with the 
operation of the instrument:

*1) 
If a sound other than these beep sound patterns is heard, refer to the instruction manual of TS-
Shield.

*2)
When auto leveling is performed by pressing {Auto leveling switch} for a long time (1 second), the 
same auto leveling operation as that performed when {Power switch} is turned ON is performed. 
Measurement by rotating the instrument 180° calibrates the inclination sensor.

Caution

Do not touch the instrument during auto leveling. Doing so may cause injury.

Auto leveling 

switch

Beep sound

*1)

While auto leveling is stopped

While auto leveling is being 

performed

Short press

One beep

After the beep sound is heard, 
auto leveling starts when you 
release the switch.

After the beep sound is heard, auto 
leveling stops when you release the 
switch.

Long press 
(1 second)

Two beeps

After the beep sound is heard, 
auto leveling starts when you 
release the switch. At this time, 
the instrument rotates 180°.*2)

Hold down

Two beeps

After the beep sound is heard, the leveling screw starts extending. It 
stops when you release the switch.

Содержание LN-100






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды