background image

Preface   

 iii

P/N: 7010-1006

Preface

Thank you for purchasing this Topcon product. The materials available in this Manual (the “Manual”) 

have been prepared by Topcon Positioning Systems, Inc. (“TPS”) for owners of Topcon products, and 

are designed to assist owners with the use of the receiver and its use is subject to these terms and 

conditions (the “Terms and Conditions”).

Terms and Conditions

Use

This product is designed to be used by a professional. The user should have a good knowledge of the 

safe use of the product and implement the types of safety procedures recommended by the local 

government protection agency for both private use and commercial job sites.

Copyrights

All information contained in this Manual is the intellectual property of, and copyrighted material of 

Topcon Positioning Systems (TPS). All rights are reserved. Do not use, access, copy, store, display, 

create derivative works of, sell, modify, publish, distribute, or allow any third party access to, any 

graphics, content, information or data in this Manual without TPS’ express written consent and may only 

use such information for the care and operation of the receiver. The information and data in this Manual 

are a valuable asset of TPS and are developed by the expenditure of considerable work, time and 

money, and are the result of original selection, coordination and arrangement by TPS.

Trademarks

Topcon

®

, Topcon Positioning Systems™, 3D-MC

® 

are trademarks or registered trademarks of TPS. 

GX-55, GX-75, MC-i4, TS-i3 are trademarks of TPS. Windows

®

 is a registered trademark of Microsoft 

Corporation. The Bluetooth

® 

word mark and logos are owned by Bluetooth SIG, Inc. and any use of 

such marks by Topcon Positioning Systems, Inc. is used under license. Other product and company 

names mentioned herein may be trademarks of their respective owners.

Disclaimer of Warranty

EXCEPT FOR ANY WARRANTIES IN AN APPENDIX OR A WARRANTY CARD ACCOMPANYING THE 

PRODUCT, THIS MANUAL AND THE RECEIVER ARE PROVIDED “AS-IS.” THERE ARE NO OTHER 

WARRANTIES. TPS DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY 

PARTICULAR USE OR PURPOSE. TPS AND ITS DISTRIBUTORS SHALL NOT BE LIABLE FOR TECHNICAL 

OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE OR USE OF THIS 

MATERIAL OR THE RECEIVER. SUCH DISCLAIMED DAMAGES INCLUDE BUT ARE NOT LIMITED TO 

LOSS OF TIME, LOSS OR DESTRUCTION OF DATA, LOSS OF PROFIT, SAVINGS OR REVENUE, OR LOSS 

OF THE PRODUCT’S USE. IN ADDITION TPS IS NOT RESPONSIBLE OR LIABLE FOR DAMAGES OR 

COSTS INCURRED IN CONNECTION WITH OBTAINING SUBSTITUTE PRODUCTS OR SOFTWARE, 

CLAIMS BY OTHERS, INCONVENIENCE, OR ANY OTHER COSTS. IN ANY EVENT, TPS SHALL HAVE NO 

LIABILITY FOR DAMAGES OR OTHERWISE TO YOU OR ANY OTHER PERSON OR ENTITY IN EXCESS OF 

THE PURCHASE PRICE FOR THE RECEIVER. 

Please read the following terms and conditions carefully.

Содержание 3D-MC








































Отзывы: