• Safe operation is no longer guaranteed when:
- the product shows obvious damage
- the product does not work properly or at all
(flickering light, emitting smoke or smell of
burning, audible crackling noise, discoloration
of the product or adjacent surfaces)
- the power supply was stored for an extended
period under adverse conditions or
- if the product was damaged during transport.
• Always disconnect the mains plug from the wall
socket before cleaning or when not using the
product for a longer period of time (e.g. when
storing).
• If you have any further questions that have not
been considered in these operating instructions,
please contact us or any other expert.
Mounting
• Fasten the clamp to a suitable surface such as the edge of a table or a windowsill.
• Turn the screw clamp clockwise until the clamp is fastened securely to the surface.
• Insert the lamp stand into the clamp holder and adjust the lamp position as required. Fasten the lamp
head using the butterfly screw.
Connection / Start-up
• Place the connection cable so that nobody can trip over it.
• Plug the mains plug into a wall mains socket.
• Switch on the lamp, using the switch on the top of the lamp.
- Position “O”: Lamp is switched off
- Position “I”: Lamp is switched on
When using the product, arrange your chair, table and the lamp in a convenient and comfortable
position to avoid eye strain and a stiff neck.
Use both eyes, which should be 20 to 25 cm away from the lens, then move the object closer to
or further from the lens until the image is clear. Wear spectacles if you normally do.
Changing the Light Source
Before replacing the light source, always disconnect the lamp from its power supply (pull the
plug out of the socket!).
Lamps that are in use become very hot! To avoid burning, allow the lamp to cool down for at least
5 minutes before you replace it.
Never use light sources with a greater output than stated in the technical data, as the lamp could
be overloaded.
• Carefully remove the protective cover at the rear of the lamp head.
• Carefully remove the defective tube from the socket.
• Then proceed in reverse order to insert the new tube.
Maintenance and care
Do not apply too much pressure to the product’s surfaces as this may cause scratching. This
especially applies to the magnifier.
• The product does not require any maintenance, do not disassemble it. Have maintenance or repair
services done by a specialist workshop only.
• Disconnect the product from the mains before cleaning; unplug the plug-in socket from the mains socket.
• Clean the exterior of the product using a clean, soft, dry cloth only. Do not use any aggressive cleaning
agents or chemical solutions as these may damage the housing causing discoloration and/or malfunc-
tion.
• Dust can be easily removed with a clean, soft brush and vacuum air.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Operating voltage ................................. 220 – 240 V/AC, 50 Hz
Tube ..................................................... 2 x 9 W, 2G7
Magnification ........................................ 1.75x, 3 dioptres
Lens dimensions ................................... 190 x 157 mm
Cable length ......................................... approx. 1.5 m
Operating temperature ......................... -5 ºC to +40 ºC
Arm length (min. / max.) ....................... approx. 45 cm / 90 cm
Weight .................................................. approx. 4.2 kg
Operating Instructions
Magnifying Lamp 2 x 9 W, 3 dioptres
Item No. 2131499
Intended Use
This product is a magnifying glass with three dioptres on arm lamp. It is intended to produce a magnified
image of objects. It needs to be firmly mounted on a suitable surface such as a table, a window shelf or a
wall. The balanced arm allows the lamp to be set to a desired position.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Magnifying lamp
• 2x PL-9W, 2G7 fluorescent tube
• Clamp
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown.
Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health, e.g. due to an
electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
The product was constructed according to protection class II.
The product may be set up and used only in dry, closed indoor spaces. The product must not get
moist or wet. There is a risk of fatal electric shock!
Safety Instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
a) General
• Due to safety and approval concerns the prod-
uct must not be modified and/or altered without
authorization.
• The lamp is not a toy; keep away from children!
Children are not able to evaluate any dangers
that can arise when handling electric devices
improperly. Use extreme caution when children
are present.
• There is also a risk of injury when the magnifier
lamp tips over/ falls down.
• Do not leave packaging material unattended, as
children could use it as a toy creating hazardous
situations.
• For installations in industrial facilities, follow the
accident prevention regulations for electrical sys-
tems and equipment of the government safety
organization or the corresponding authority for
your country.
b) Operation
• The product may be set up and used only in
dry, closed indoor spaces. The product must not
get moist or wet. There is a risk of fatal electric
shock!
• Never connect or disconnect the mains plug with
wet hands.
• Do not use the product in rooms or under ad-
verse ambient conditions, where combustible
gas, smoke or dust are or could be present!
There is a risk of explosion!
• Protect the product from extreme temperatures,
strong vibrations or strong mechanical stress.
• Never use the product immediately after it has
been brought from a cold room into a warm one.
The condensation generated could destroy the
product. There is also a risk of lethal electric
shock!
• Allow the device to reach room temperature
before connecting and using it. This may take
several hours.
• Never pour liquids above or near the product.
• Never place the product on an unstable or mov-
ing surface. Install the magnifier lamp in such a
way that it cannot tip over or fall down. Choose a
horizontal, flat and stable surface.
• Tipping over/ falling down could cause injuries
and on top of that will damage the product.
• Connect the power adapter to a wall socket that
can be accessed easily.
• Do not pull the cable when disconnecting the
mains plug from the wall socket.
• Protect the mains cable from sharp objects or
edges. Route the cable in such a way that it does
not present any trip hazards.
• Never carry the product by its cable.
• Do not hang any objects (e.g. decorative materi-
als) on the magnifier lamp.
• Do not use the magnifier lamp to look into bright
light sources; there is a risk of eye injury.
• When not using the magnifier, always cover it
with the hinged lid. Otherwise there is a risk of
fire when exposed to sunlight, since the magni-
fier has the same effect as a burning lens.
• Disconnect the wall socket to which the product
is connected on all poles (turn off the respective
safety device or unscrew the fuse, and then turn
off the ground fault circuit interrupter). Do only
then disconnect the mains plug from the wall
socket.
• Should a safe operation of the product be no
longer possible, take the product out of operation
and secure it against accidental use.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*2131499_v1_0619_02_dh_m_en
