Tolomatic STAC6 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 82

background image

STAC6 Drives and Microstepping Motors:

User Manual

(Discontinued Product)

• 1.2 •

1:

H A R D W A R E

be damaged by incorrect handling. Discharge yourself before touching
the product. Avoid contact with high insulating materials (artificial
fabrics, plastic film, etc.). Place the product on a conductive surface.

During operation keep all covers and cabinet doors shut. Otherwise,

there are deadly hazards that could possibly cause severe bodily
damage or damage to the product.

In operation, depending on the degree of enclosure protection, the

product can have bare components that are live or have hot surfaces.
Control and power cables can carry a high

voltage

even when the motor is not rotating.

Never pull out or plug in the product while the system is live. There is a

danger of electric arcing and danger to persons and contacts.

After powering down the product, wait at least ten minutes before

touching live sections of the equipment or undoing connections (e.g.,
contacts, screwed connections). Capacitors can store dangerous
voltages for long periods of time after power has been switched off. To
be safe, measure the contact points with a meter before touching.

Be alert to the potential for personal injury. Follow the recommended
precautions and safe operating practices.
Safety notices in this manual provide important information. Read and
be familiar with these instructions before attempting installation,
operation, or maintenance. The purpose of this section is to alert users
to possible safety hazards associated with this equipment and the
precautions that need to be taken to reduce the risk of personal injury
and damage to the equipment.

Failure to observe these precautions could result in serious bodily injury,

damage to the equipment,or operational difficulty.

«
...
11
12
13
14
15
...
»

Содержание STAC6



















































































Отзывы:

Нет отзывов

Похожие инструкции для STAC6

Бренд: M+S Страницы: 6

Бренд: Wacker Neuson Страницы: 70

Бренд: Briggs & Stratton Страницы: 10

Бренд: Team Orion Страницы: 2

4-STROKE AIR-COOLED GASOLINE ENGINE

Бренд: E-Z-GO Страницы: 100

Бренд: Franklin Страницы: 114

Бренд: Mitsubishi Страницы: 61

Бренд: DANA Страницы: 2

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Volvo Penta Страницы: 176

Бренд: Barrus Страницы: 50

Бренд: Hotsy Страницы: 70

Бренд: KEM Страницы: 61

Бренд: Vascat Страницы: 64

Бренд: Jets Munt Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды