background image

 

FCC STATEMENT 
FCC declaration of conformity 

Responsible party: 
4Sight, Inc 
3325 E. Shelby St. 
Ontario, CA 91764 
(909) 944-5511 Fax: (866) 285-5828 

This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, including 

interference that may cause undesired operation. 

Note: 
This equipment has been tested and found to comply with the limits for Class B 
digital devices, pursuant to Part 15 of the FCC rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following 
measures: 

 Reorient or relocate the receiving antenna 

 Increase the separation between the equipment and receiver 

 Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected 

 Consult the dealer or an experienced radio/TV technician for help2 

Use of shielded cable is required to comply with Class B limits in Subpart B of 
Part 15 of the FCC rules. 
Do not make any changes or modifications to the equipment unless otherwise 
specified in the manual. If such changes or modifications should be made, you 
could be required to stop operation of the equipment. 

Canada 
Industry Canada (IC) 
Unintentional emitter per ICES-003/NMB-003 
This digital apparatus does not exceed the Class B limits for radio noise 
emissions from digital apparatus as set out in the radio interference regulations 
of Industry Canada. 

Le present appareil numerique n'emet pas de bruits radioelectriques depassant 
les limites applicables aux appareils numeriques de Classe B prescrites dans le 
reglement sur le brouillage radioelectrique edicte par Industrie Canada. 

 

18

Содержание 4SKCO1
























Отзывы: