TLV MC-COSR-16 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 38

background image

172-65185A-08 (MC-COSR Multi-control Valve) 20 Nov 2014

12

Installation

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use hoisting equipment for heavy objects (weighing approximately

20 kg (44 lb) or more). Failure to do so may result in back strain or other

injury if the object should fall.

CAUTION

Take measures to prevent people from coming into direct contact with

product outlets. Failure to do so may result in burns or other injury from

the discharge of fluids.

CAUTION

Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.

Installation Environment

Avoid installation in the following types of environments:



Locations with ambient temperatures above 50 °C (122 °F) or below 0 °C (32 °F)



Locations with ambient humidity above 90% RH and below 10% RH



Locations where corrosive gas is generated



Locations with heavy vibration or shock



Locations with high inductive interference or other factors that would have a
harmful effect on electrical circuitry

1. Blowdown

Before installing the MC-COSR, be
sure to blow down all piping
thoroughly. If this is not possible,
perform a blowdown using the
bypass valve.
Blowdown is especially important
for newly installed piping or after
the system has been shut down for
a long period of time.

開

閉

閉

バイパス配管利用のブロー

M C -C O SR

Open

Closed

Closed

Blowdown with the Bypass Valve

2. Removing Seal and Cap

Before installation, be sure to remove all protective seals and caps
covering the product inlet and outlets. (Found in 2 locations.)

①

②

3.

Installation Angle

Install the MC-COSR vertically, so that the arrow mark on
the body points horizontally in the direction of steam flow.
Allowable inclination is 10 degrees in the fore-aft direction
and 15 degrees side to side in the plane perpendicular to
the steam flow line.

«
...
11
12
13
14
15
...
»

Содержание MC-COSR-16







































Отзывы:

Нет отзывов

Похожие инструкции для MC-COSR-16

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды