background image

 

 

172-65450MA-06  (JH5SL-P/JH5SH-P)    8  Nov  2021 

1

 

Contents

 

Introduction ....................................................................... 1

 

Checking the Piping .......................................................... 4

 

Operation .......................................................................... 5

 

Specifications .................................................................... 6

 

Configuration ..................................................................... 6

 

Installation ......................................................................... 7

 

Maintenance ...................................................................... 8

 

Disassembly/Reassembly ................................................. 9

 

Instructions for Plug/Holder Disassembly and Reassembly ... 12

 

Troubleshooting .............................................................. 13

 

TLV EXPRESS LIMITED WARRANTY ........................... 14

 

Service ............................................................................ 16

 

Options ............................................................................ 17

 

 

Introduction 

Thank you for purchasing the TLV free float steam trap. 

This product has been thoroughly inspected before being shipped from the factory. 
When the product is delivered, before doing anything else, check the specifications and 
external appearance to make sure nothing is out of the ordinary. Also be sure to read 
this manual carefully before use and follow the instructions to be sure of using the 
product properly. 

This instruction manual is edited based on the JH-P Series (with cover plug). The JH-W 
Series (with socket welded cover connection), JH-F Series (with flanged cover 
connection) and JH-V Series (with manual air vent valve) are described at the end of this 
manual in the 'Option

’ section.   

This  free  float  steam  trap  employs  a  hinge-less  and  lever-less  free  float  to  rapidly, 
automatically  and  continuously  discharge  the  inflowing  condensate  that  is  continuously 
generated  inside  the  equipment,  thus  preventing  the  accumulation  of  condensate  and 
thereby improving the heat transfer efficiency of the equipment. 

This  steam  trap  also  employs  a  precision-ground  float  and  three-point  seating  that 
supports  the  float  securely  at  three  points  and  ensures  a  high  degree  of  sealing  when 
even only minute quantities of condensate are present. 

This free float steam trap is suitable for applications with the introduction of almost no air 
(such as process systems and steam-using equipment under long continuous operation, 
or superheated and saturated steam mains, branches and trace lines). 

If detailed instructions for special order specifications or options not contained in this 
manual are required, please contact TLV for full details. 

This instruction manual is intended for use with the model(s) listed on the front cover. It 
is necessary not only for installation but for subsequent maintenance, 
disassembly/reassembly and troubleshooting. Please keep it in a safe place for future 
reference.

Содержание JH5SH-F





















Отзывы: