background image

172-65606A-02 (JAH5RA-R/JAH7RA-R)    12 January 2021 

 

 

 

 

Manufacturer 

 

 

881 Nagasuna, Noguchi, Kakogawa, Hyogo, 675-8511 Japan 

Tel: [81]-(0)79-422-1122    Fax: [81]-(0)79-422-0112 

 

Copyright © 2021 by TLV CO., LTD. All rights reserved 

 

Free Float Drain Trap   

JAH5RA-R 
JAH7RA-R 

 

Introduction 

Thank you for purchasing the TLV free float drain trap. 

This product has been thoroughly inspected before being shipped from the factory. 
When the product is delivered, before doing anything else, check the specifications 
and external appearance to make sure nothing is out of the ordinary. Also be sure to 
read this manual carefully before use and follow the instructions to be sure of using 
the product properly. 

This product is designed, manufactured, and inspected for use with air, inert 
gases and condensate. Do not use for toxic, flammable or otherwise 
hazardous fluids. Hereafter in this manual, the words 

“gas” and “gases” 

should be read as 

“inert gas” and “inert gases”. 

This free float drain trap employs a precision-ground float and three-point seat. With no 
hinges or levers, the trap automatically and continuously discharges condensate as it 
forms in the air/gas system, preventing it from backing up in the system. The three-
point seat supports the precision-ground float at three points, ensuring an air-tight seal 
even under extremely low condensate loads. This free float drain trap is also inline 
repairable, facilitating repair and maintenance, resulting in considerable time savings. 

If detailed instructions for special order specifications or options not contained in this 
manual are required, please contact TLV for full details. 

This instruction manual is intended for use with the model(s) listed on the front cover. 
It is necessary not only for installation but for subsequent maintenance, 
disassembly/reassembly and troubleshooting. Please keep it in a safe place for 
future reference. 
 

Содержание JAH5RA-R

















Отзывы: