TLV COS-16 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 31

background image

172-65175MA-13 (COS Pressure Reducing Valve) 16 Feb 2022

19

Disassembling the Piston Section

Remove the pilot body after loosening and removing the bolts (stud bolts).
During this process, pay attention not to lose the connecting tubes (2).

Remove the piston, cylinder and the silencer (for 65 to 100 mm (2

1

/

2

to 4 in) only)

from the body. Then remove the piston rings and the tension rings from the piston.
Do not apply too much force when removing the piston rings and tension rings.



Check for the interior of the cylinder, the exterior of the piston rings, the small hole

on the piston and the gaskets for any fault or abnormality.

15 to 50 mm (

1

/

2

to 2 in)

65 to 100 mm (2

1

/

2

to 4 in)

Piston

Cylinder

Connecting
Tube

Gasket

Piston Ring

Tension Ring

Piston Ring

Tension Ring

Connecting

Tube

Gasket

Piston

Cylinder

Connecting
Tube

Gasket

Piston Ring

Tension Ring

Piston Ring

Tension Ring

Connecting

Tube

Gasket

Screen
(as a silencer)

Seal Ring

«
...
18
19
20
21
22
...
»

Содержание COS-16
































Отзывы:

Нет отзывов

Похожие инструкции для COS-16

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Handicare Страницы: 56

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: MAKOT Страницы: 6

Бренд: Omegalink Страницы: 2

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

Бренд: ECKELMANN Страницы: 147

Бренд: Anthem Страницы: 8

Бренд: National Instruments Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды