TLV COS-16 Скачать руководство пользователя страница 28

Страница: 28 / 31

172-65175MA-13 (COS Pressure Reducing Valve) 16 Feb 2022

Problem

Symptom

Cause

Remedy

Faulty steam
trap

Steam is blowing

There is a build-up of dirt
on the trap valve seat or
at the float base

Clean

The body is installed
tilted

Check the piping

The float is deformed

Check for water hammer
Replace with a new float

There is vibration in the
piping

Secure the piping

No condensate is
discharged

The primary pressure
exceeds the trap valve
seat maximum working
pressure

Adjust primary pressure

Water is inside the float

Replace with a new float

The outlet piping is
clogged

Check the piping
Clean

The trap valve seat is
clogged

Clean
Replace with a new trap
valve seat

NOTE: When replacing parts for the COS-3, COS-16 and COS-21, use the parts list for

reference, and replace with new parts from the kits shown there. Please note that
replacement parts for the COS-3, COS-16 and COS-21 are only available as part of a
replacement parts kit.

Содержание COS-16































Результаты поиска

Содержание COS-16

Отзывы:

Похожие инструкции для COS-16

Бренды по названию

Популярные бренды

TLV COS-16, Инструкция по эксплуатации

Результаты поиска

Содержание COS-16

Отзывы:

Похожие инструкции для COS-16

Бренды по названию

Популярные бренды