background image

 

172-65634MAJ-03  (A-DR20)    6  Oct  2021

 

2

 

Safety Considerations 

  Read this section carefully before use and be sure to follow the 

instructions. 

  Installation, inspection, maintenance, repairs, disassembly, adjustment 

and valve opening/closing should be carried out only by trained 
maintenance personnel

.

 

  The precautions listed in this manual are designed to ensure safety and 

prevent equipment damage and personal injury. For situations that may 
occur as a result of erroneous handling, three different types of cautionary 
items are used to indicate the degree of urgency and the scale of potential 
damage and danger: DANGER, WARNING and CAUTION. 

  The three types of cautionary items above are very important for safety: be 

sure to observe all of them as they relate to installation, use, maintenance, 
and repair. Furthermore, TLV accepts no responsibility for any accidents or 
damage occurring as a result of failure to observe these precautions. 

Symbols 

 

Indicates a DANGER, WARNING or CAUTION item. 

 

Indicates an urgent situation which poses a threat of death or 
serious injury 

 

Indicates that there is a potential threat of death or serious injury 

 

Indicates that there is a possibility of injury or equipment / product 
damage 

 

 

Install properly and DO NOT use this product outside the 
recommended operating pressure, temperature and other 
specification ranges. 

Improper use may result in such hazards as damage to the product   
or malfunctions that may lead to serious accidents. Local regulations 
may restrict the use of this product to below the conditions quoted. 

Take measures to prevent people from coming into direct 
contact with product outlets. 

Failure to do so may result in burns or other injury from the 
discharge of fluids.

 

When disassembling or removing the product, wait until the 
internal pressure equals atmospheric pressure and the 
surface of the product has cooled to room temperature

Disassembling or removing the product when it is hot or under 
pressure may lead to discharge of fluids, causing burns, other 
injuries or damage.

 

Be sure to use only the recommended components when 
repairing the product, and NEVER attempt to modify the 
product in any way. 

Failure to observe these precautions may result in damage to the 
product and burns or other injury due to malfunction or the 
discharge of fluids.

 

Continued on the next page 

 

DANGER 

 

WARNING 

 

CAUTION 

 

CAUTION 

Содержание A-DR20-10





















Отзывы: