background image

 

172-65634MAJ-03  (A-DR20)    6  Oct  2021

 

18

 

REPORTED TO THE SELLER IN WRITING WITHIN THE WARRANTY PERIOD, 
INCLUDING A DETAILED WRITTEN DESCRIPTION OF THE CLAIMED DEFECT AND 
HOW AND WHEN THE CLAIMED DEFECTIVE PRODUCT WAS USED; AND (b) THE 
CLAIMED DEFECTIVE PRODUCT AND A COPY OF THE PURCHASE INVOICE IS 
RETURNED TO THE SELLER, FREIGHT AND TRANSPORTATION COSTS PREPAID, 
UNDER A RETURN MATERIAL AUTHORIZATION AND TRACKING NUMBER ISSUED BY 
THE SELLER. ALL LABOR COSTS, SHIPPING COSTS, AND TRANSPORTATION COSTS 
ASSOCIATED WITH THE RETURN OR REPLACEMENT OF THE CLAIMED DEFECTIVE 
PRODUCT ARE SOLELY THE RESPONSIBILITY OF BUYER OR THE FIRST END USER. 
THE SELLER RESERVES THE RIGHT TO INSPECT ON THE FIRST END USER’S SITE 
ANY PRODUCTS CLAIMED TO BE DEFECTIVE BEFORE ISSUING A RETURN MATERIAL 
AUTHORIZATION. SHOULD 

SUCH INSPECTION REVEAL, IN THE SELLER’S 

REASONABLE DISCRETION, THAT THE CLAIMED DEFECT IS NOT COVERED BY THIS 
WARRANTY, THE PARTY ASSERTING THIS WARRANTY SHALL PAY THE SELLER FOR 
THE TIME AND EXPENSES RELATED TO SUCH ON-SITE INSPECTION. 

Exclusion of Consequential and Incidental Damages 

IT IS SPECIFICALLY ACKNOWLEDGED THAT THIS WARRANTY, ANY OTHER EXPRESS 
WARRANTY NOT NEGATED HEREBY, AND ANY IMPLIED WARRANTY NOT NEGATED 
HEREBY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE, DO NOT COVER, AND NEITHER TLV, TII NOR 
ITS TLV GROUP COMPANIES WILL IN ANY EVENT BE LIABLE FOR, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO LOST PROFITS, THE 
COST OF DISASSEMBLY AND SHIPMENT OF THE DEFECTIVE PRODUCT, INJURY TO 
OTHER PROPERTY, DAMAGE TO BUYER’S OR THE FIRST END USER’S PRODUCT, 
DAMAGE TO BUYER’S OR THE FIRST END USER’S PROCESSES, LOSS OF USE, OR 
OTHER COMMERCIAL LOSSES. WHERE, DUE TO OPERATION OF LAW, 
CONSEQUENTIAL AND INCIDENTAL DAMAGES UNDER THIS WARRANTY, UNDER ANY 
OTHER EXPRESS WARRANTY NOT NEGATED HEREBY OR UNDER ANY IMPLIED 
WARRANTY NOT NEGATED HEREBY (INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) CANNOT BE 
EXCLUDED, SUCH DAMAGES ARE EXPRESSLY LIMITED IN AMOUNT TO THE 
PURCHASE PRICE OF THE DEFECTIVE PRODUCT. THIS EXCLUSION OF 
CONSEQUENTIAL AND INCIDENTAL DAMAGES, AND THE PROVISION OF THIS 
WARRANTY LIMITING REMEDIES HEREUNDER TO REPLACEMENT, ARE 
INDEPENDENT PROVISIONS, AND ANY DETERMINATION THAT THE LIMITATION OF 
REMEDIES FAILS OF ITS ESSENTIAL PURPOSE OR ANY OTHER DETERMINATION 
THAT EITHER OF THE ABOVE REMEDIES IS UNENFORCEABLE, SHALL NOT BE 
CONSTRUED TO MAKE THE OTHER PROVISIONS UNENFORCEABLE. 

Exclusion of Other Warranties 

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 
AND ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, 
ARE EXPRESSLY DISCLAIMED. 

Severability 

Any provision of this warranty which is invalid, prohibited or unenforceable in any 
jurisdiction shall, as to such jurisdiction, be ineffective to the extent of such invalidity, 
prohibition or unenforceability without invalidating the remaining provisions hereof, 
and any such invalidity, prohibition or unenforceability in any such jurisdiction shall 
not invalidate or render unenforceable such provision in any other jurisdiction.   

Содержание A-DR20-10





















Отзывы: