background image

WHEEL REPLACEMENT (DIAGRAM T)

1.  Loosen set screw from wheel hub by using a 5/32” allen wrench.
2. Twist wheel to loosen and pull off of motor shaft.  

Do not pull too hard; wheel may bend

.  Wheels “fused” to shaft may require

penetrating oil and/or a wheel puller to facilitate removal.

3. Slide new wheel on to flat of shaft and firmly tighten set screw.  

MOTOR OILING 

The SideShot motor is permanently lubricated and requires no oiling.

LIMITED PARTS WARRANTY AND CLAIM PROCEDURE

Tjernlund Products, Inc. warrants the components of the SS1R for two years from date of installation.  This warranty covers
defects in material and workmanship.  This warranty does not cover normal maintenance, transportation or installation charges  for
replacement parts or any other service calls or repairs.  This warranty DOES NOT cover the complete SS1R if it is operative,
except for the defective part.

Tjernlund Products, Inc. will issue credit or provide a free part to replace one that becomes defective during the two year warranty
period.  Proof of date of the installation in the form of the contractor sales/installation receipt is necessary to prove the unit has
been in service for under two years.  All receipts should include the date code of the SS1R to ensure that the defective component
corresponds with the complete unit.  This will help preclude possible credit refusal.

1.) Follow troubleshooting guide to determine defective component.  If unable to determine faulty component, contact your 

Tjernlund distributor or Tjernlund Products Technical Customer Service Department  at 1-800-255-4208 for troubleshooting 
assistance.

2.) After the faulty component is determined, return it to your Tjernlund distributor for replacement.  Please include SS1R 

date code component was taken from.  The date code is located on the Electrical Box cover plate.  If the date code is older 
than 2 years you will need to provide a copy of the original installation receipt to your distributor.  Credit or replacement will 
only be issued to a Tjernlund distributor after the defective part has been returned prepaid to Tjernlund.

COVERED PARTS

Component

Part Number

SS1 Series Motor with Wheel  

950-0625

SS1 Series Wheel

950-0635

SS1R Proving Switch

950-0750

High Limit Switch

950-0640

UC1 Universal Control Circuit Board

950-8804

Oil Solenoid 

For "D" series oil furnaces (-OBD-XXX, -OPD-XXX and etc.)

950-0690

Oil Solenoid 

For "F" series oil furnaces (-OBF-XXX, -OPF-XXX and etc.)

Contact Rheem/Prostock 

parts department for solenoid part number.

WHAT IS NOT COVERED

Product installed contrary to our installation instructions, altered, neglected or misused
Product that has been wired incorrectly
Product that has been damaged by a malfunctioning or maladjusted burner
Any freight charges related to the return of the defective part
Any labor charges related to evaluating and replacing the defective part

19

Contact Tjernlund
Products, Inc. for
SS1R components not
referenced to the left.

TJERNLUND LIMITED TWO  YEAR WARRANTY

Tjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from defects due to faulty
material or workmanship for a period of (2) years from the date of original purchase or delivery to the original purchaser,
whichever is earlier.  Remedies under this warranty are limited to repairing or replacing, at our option, any product which shall,
within the above stated warranty period, be returned to Tjernlund Products, Inc. at the address listed below, postage prepaid.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, AND TJERNLUND
PRODUCTS, INC. EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OF THIS PRODUCT.  THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND NO AGENT IS
AUTHORIZED TO ASSUME FOR US ANY LIABILITY ADDITIONAL TO THOSE SET FORTH IN THIS LIMITED WARRANTY.
IMPLIED WARRANTIES ARE LIMITED TO THE STATED DURATION OF THIS LIMITED WARRANTY.  Some states do not
allow limitation on how long an implied warranty lasts, so that limitation may not apply to you.  In addition, some states do not
allow the exclusion or limitation of incidental or consequential damages, so that above limitation or exclusion may not apply to
you.  This warranty gives you specific legal rights and you may also have other rights which may vary from State to State.  Send
all inquiries regarding warranty work to Tjernlund Products, Inc. 1601 9th Street, White Bear Lake, MN 55110-6794.  Phone (651)
426-2993 • (800) 255-4208 • Fax (651) 426-9547 • Email [email protected].

Содержание SS1R SIDESHOT (DISCONTINUED VERSION-PRE UC1 UNIVERSAL CONTROL) 8504046 REV 0595
























Отзывы: