Titgemeyer MS 100 Скачать руководство пользователя страница 31

Страница: 31 / 45

Maintaining the riveting tool

Refilling hydraulic oil

Attention

Environmental hazard! Always use a large bowl for collecting
oil. Please observe all the environmental regulations prevalent
in the respective area.

Attention

Material damage! Do not let the O-ring (8) be damaged. If the
O-ring gets damaged, then replace immediately.

• Unscrew the socket head screw (7) in the hydraulic housing carefully,

using the internal hex key SW4 (19).

• Screw the oil refill adapter screw (17) into the free opening.
• Set the filled oil gun (16).
• Screw socket head screw (7) out of the device floor with the internal hex

key SW4 (19).

• Insert the crank (18) into the free opening and screw up to the limit.
• Pull crank (18) out until the marking is flush with the floor plate.

Note

By this piston movement hydraulic oil (e.g. ELFOLNA 46 or
equivalent) is drained into the hydraulic area from the plugged
in oil gun

• Press oil gun (16) remove and screw out oil refill adapter screw (17).
• Screw socket head screw (7) with O-ring (8) into hydraulic housing and

tighten with internal hex key SW4 (19) (see page 33 “Table for torque
values”).

Environmental

hazard

Содержание MS 100














































Результаты поиска

Содержание MS 100

Отзывы:

Похожие инструкции для MS 100

Бренды по названию

Популярные бренды

Titgemeyer MS 100, Руководство по эксплуатации

Результаты поиска

Содержание MS 100

Отзывы:

Похожие инструкции для MS 100

Бренды по названию

Популярные бренды