background image

OPERATION INSTRUCTIONS

 

NOTE: 

Before using the tool, read the 

instruction book carefully.

Warning:

 

Before working your tool 

make sure that no power cords will 

be damaged. Before mounting or replacing 
application tools or accessories, pull the  
power plug.This preventative safety measure 
eliminates danger from accidentally starting 
the power tool.

Do not touch the gear box after long working time, 
because it could be hot.

1. MOUNTING ACCESSORIES

Caution: 

For all work or when changing 

application tools, always wear protective 

gloves. Avoid danger of injury from the sharp edges 
of the application tools. Application tools can become 
very hot while working, presenting danger of burns!

Warning: To reduce the risk of injury, do 
not let the Universal end cut blades or 

any segment saw blades face back toward the 
user’s hand.

- Loosen the flange

Use the Hex Key to rotate the flange clockwise.(See Fig. 1)

- Insert Accessories    

                                   

For the accessories with machine and most other 
branded accessories, the flange must be completely 
removed  to  install  accessory  (See  Fig.  2).                                                                                                                    

Note: 

For the Universal-Fit

TM

 Accessory

Insert the Accessory onto the Universal-Fit

TM 

Accessory 

Interface.(See Fig. 4)

- Tighten the flange

Use the Hex Key to rotate the flange counterclockwise 
until accessory is tightened securely.(See Fig. 3)
 

2. MOUNTING / CHANGING THE SANDING 
SHEET (See Fig. 5)

Align the sanding sheet and press it onto the sanding 
pad by hand.
Firmly press the power tool with the sanding sheet 
against a flat surface and briefly switch the power 
tool on. This provides for good adhesion and prevents 
premature wear.
If one point has become worn, pull off the sanding 
sheet, turn it 120° and replace.

a

1

1

2

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Содержание TTB507HTL



















Отзывы: