manualshive.com logo in svg

Titan 1.866.345.8484, Руководство по эксплуатации, Страница: 13 / 15

Поделиться
Скачать
Titan 1.866.345.8484 Скачать руководство пользователя страница 13

www.

TITAN

TI

.com

1.866.345.8484

SUPERIOR 

BOLTING SOLUTIONS

12

www.

TITAN

TI

.com

1.866.345.8484

SUPERIOR 

BOLTING SOLUTIONS

12. Release the hydraulic pressure from the cylinder and the center foot 

will retract.

13.  Install the dowel pin (7) in the hole on the side of the housing (8), 

use a hammer if necessary. The dowel pin will ride in the slot on the side 

of the piston (6), if everything is properly assembled.

14. Check the feet again to be sure they are still aligned. Check the 

alignment of the cylinder in reference to the housing (this should have 

been marked in disassembly). Insert the set screw (9) in the hole pro-

vided in the front of the housing (8). Tighten the set screw to the cylinder. 

Do not tighten the set screw too tight, or future removal of the cylinder 

may be diffi cult.

15. Pressurize and de-pressurize the cylinder to check that the tool is 

operating properly.

Trouble Shooting

General Notes:

 - Do not twist or bend hoses too sharply.

 - Pay close attention to keeping all parts clean internally  

                           

   and externally. (Dirt and foreign matter are the most 

   common causes of trouble in hydraulic systems)

 - Make sure all quick couplers are always completely 

   coupled together.

12

Содержание 1.866.345.8484
















Отзывы:

Нет отзывов