background image

  

SteamMaster

 

5

Prior to the steam being produced a small 

amount of bubbling will occur at the 

steamplate.

WARNING!  Beware of hot 

water discharge prior to steam 

emission.

When the steam has been produced, lift the 

steam plate above the level of the tank outlet 

to allow condensed steam to run back down 

the hose and into the tank.
If you are right-handed hold the steamplate in 

your left hand and place flat against the wall 

where you wish to commence removing.
Leave the steamplate against the wall for 

approximately 10 seconds. If you are left 

handed you may find it easier to operate with 

the other hand.

Move the 

steamplate 

to the section 

immediately next 

to where you 

have just been 

working and use a 

wallpaper scraper 

to remove the 

section that has just been steamed. By working 

in this way you should be able to remove 

paper continually. You may have to leave 

the steamplate against the wall for longer 

periods with some papers or re-steam if not 

completely removed.
The water level is shown through the glass 

level indicator and should not be allowed to fall 

below MIN. Switch the unit off when this level 

has been reached.
If you require further use of the steamer, allow 

the unit to cool for a minimum of 5 minutes. 

Remove the filler cap carefully.

Beware of STEAM! Refill to the 

level indicator as before and 

follow the above instructions.

YOU MUST NEVER ALLOW THE 

UNIT TO BOIL DRY.

There is a safety thermal cut-out device fitted 

to the unit. If the unit is allowed to boil dry this 

will operate and prevent further use. Switch the 

unit off and allow it to cool for at least 5 minutes, 

refill with water and then switch on again - the 

thermal cut-out should automatically re-set. 

If this has not re-set allow a further cooling 

period.
When you have finished using the unit allow 

any remaining water to cool and then empty 

the unit. We recommend flushing the tank out 

with clean water before storing. NEVER LEAVE 

WATER IN THE UNIT WHILE BEING STORED.

FILLER CAP

To fit - screw onto the filler neck hand-tight. Do 

not over-tighten.
To remove - ensure unit is switched off and 

has stopped boiling. Wait for 5 minutes. Slowly 

unscrew the cap, any remaining trapped steam 

will be released from beneath the cap.

CAUTION! Steam is very hot 

- wear a glove and keep face 

clear. Refill to the level indicator 

as before and follow above 

instructions.

Содержание 0LMB150NA

























Отзывы: