5
8
RECYCLING BUTTONS
Recycle ‘ON’ Time Setting – Press button to set the ‘ON’ time for the Recycling
Timer Output. Press Enter/Reset to accept setting.
Recycle ‘OFF’ Time Setting – Press button to set the ‘OFF’ time for the Recycling
Timer Output. Press Enter/Reset to accept setting.
Overide Recycle Timer – Press and hold this button for approximately 2 seconds
to manually activate and/or deactivate the Recycling Timer Output. Press
Override Recycling Timer button again to return to normal operation. This is a
manual override for testing the recycling devices.
Day/Night/24 Hour – Press button to select Day/Night OR 24-hour mode. Press
Enter/Reset to accept setting.
Recycle Timer Mode – Press button to select Stop or Continue mode for
Recycling Output. Press Enter/Reset to accept setting.
Press For Temp – Press button to display current room temperature.
ADJUSTING THE SETTINGS:
Your Hades
™
2 has been
pre-set at the factory
with the following settings:
• Recycle ‘ON’ Time Setting = 1 minute
• Recycle ‘Off’ Time Setting = 60 minutes (1 hour)
• Recycle Timer Mode = Stop
• Day/Night/24 Hour Setting = Day
• Hot Start Delay = 10 minutes
• Maximum Temp Setting = 90°F
If you ever want to return the Hades
™
2 to the factory settings, do the following:
Press and hold the Enter/Reset & Down buttons at the same time until the LED
reads (
f.Set
). Press the Enter/Reset button again to restore the Hades
™
2 to the
factory settings. Once the Hades
™
2 reset is complete, the LED screen will read
(doNE
).
To adjust your Hades
™
2 to your own customized settings, do the following:
LIGHTING BUTTONS
• Turn Lights ‘On’ Time = Press the Turn Lights ON Time button. The first two
digits (hour) on the LCD will blink. Use the UP or DOWN button to set the
hour
that you’d like your lights to come ‘ON’. Press the Enter/Reset button
to lock in the new setting. Next the middle two digits (minutes) will blink. Use
the UP or DOWN button to set the
minute
that you’d like your lights to come
‘ON’. Press the Enter/Reset button to lock in the new setting. Next the last
two digits (seconds) will blink. Use the UP or DOWN button to set the
second
that you’d like your lights to come ‘ON’. Press the Enter/Reset button to lock
in the new setting. Finally, the AM/PM will blink. Use the UP or DOWN button
enheit, press and hold the UP and DOWN keys simultaneously for approxi-
mately 3 seconds.
Troubleshooting Tips
1. The Hades
™
2 has no power?
Verify power source is providing 120 Volts
A/C. Reset the circuit breaker on the Hades
™
2 by turning OFF the unit, than
turn ON.
2. What if the recycle timer is not keeping the right time?
The CR1220 (3
Volt) Lithium battery, located on the internal circuit board that is connected
to the inside of the front faceplate, may need to be replaced. The normal
lifespan of the batteries is approximately 5 years.
3. Why is the display showing ‘
Hot_F
’?
The Maximum Temp Setting has
been exceeded. When this occurs, the LIGHTS ON outputs will remain off,
until the Maximum Temp Setting function is reset by holding the Enter/Reset
button for approximately 2 seconds.
4. Why is the display showing, ‘
Err.TEP
’?
The remote sensor is not connect-
ed or not communicating with the Hades
™
2. Unhook sensor from Hades
™
2,
than reconnect it to the controller. Verify that the cable is not compromised
and that the remote sensor has power.
5. Does the temperature sensor need to be calibrated?
No. The tempera-
ture sensor is digital and there is no need for calibration.
6. My temperature is reading quite high?
Verify that the sensor is not in a
location with direct exposure to intense light and that there is air circulating
freely around it.
Controller Specifications
• Size = 9”H x 7”W x 3 ¾ ”D
• Input Voltage = 120 Volts A/C
• Output Voltage =120 Volts A/C
• Maximum Amperage = 14.5 Amps
• Remote Probe Cable Length = 3 feet
• Maximum Lighting Watts = 1200W
• ON Time Range = 1 second to 96 hours
• OFF Time Range = 1 second to 96 hours
• Lithium Battery Life = 5 years
