7
6
7
6
to set
AM
or
PM
. Press the Enter/Reset button to lock in the new setting.
NOTE: The two Lighting Outputs have a 30 second pre-set time delay
between the two receptacles to reduce start-up surges and high in-rush
current caused by ballasts.
• Turn Lights ‘Off’ Time – Press the Turn Lights Off Time button. The first two
digits (hour) on the LCD will blink. Use the UP or DOWN button to set the
hour
that you’d like your lights to go ‘OFF’. Press the Enter/Reset button to lock in
the new setting. Next the middle two digits (minutes) will blink. Use the UP or
DOWN button to set the
minute
that you’d like your lights to go ‘OFF’. Press
the Enter/Reset button to lock in the new setting. Next the last two digits
(seconds) will blink. Use the UP or DOWN button to set the
second
that you’d
like your lights to go ‘OFF’. Press the Enter/Reset button to lock in the new
setting. Finally, the AM/PM will blink. Use the UP or DOWN button to set
AM
or
PM
. Press the Enter/Reset button to lock in the new setting.
• Hot Start Delay – Press the Hot Start Delay button to display the current
setting. This mode button is used to prevent ‘Hot Starts’ from occurring by
allowing the HID lamps to cool before re-striking. This function is not activated
unless there is a power failure situation. Use the UP and DOWN buttons to
change the setting. Press the Enter/Reset button to lock in the new setting.
• Override Light Timer – Press the Override Light Timer button to bypass the
Day and Night modes. Press the button for approximately 2 seconds to switch
the Hades
™
2 from Night to Day mode or Day to Night mode (depending on
current status). Press Override Light Timer button again to return to normal
operation.
• Set Clock – To program internal clock to correct time press the Set Clock
button. The first two digits (hour) on the LCD will blink. Use the UP or DOWN
button to set the current
hour
. Press the Enter/Reset button to lock in the new
setting. Next the middle two digits (minutes) will blink. Use the UP or DOWN
button to set the current
minute(s)
. Press the Enter/Reset button to lock in the
new setting. Next the last two digits (seconds) will blink. Use the UP or DOWN
button to set the current
second(s)
. Press the Enter/Reset button to lock in
the new setting. Finally, the AM/PM will blink. Use the UP or DOWN button
to set
AM
or
PM
. Press the Enter/Reset button to lock in the new setting.
IMPORTANT:
Verify that internal clock is set to correct time of day or Outputs
will not function properly.
• Maximum Temp Setting – Press the Maximum Temp Setting button to display
the current setting. Use the UP and DOWN buttons to adjust the setting. Press
the Enter/Reset button to lock in the new setting. This is a hi-temp shut-off
feature to protect your garden for overheating.
RECYCLING BUTTONS
• Recycling ‘ON’ Time Setting – Press the Recycling ‘ON’ Time Setting button to
display the current setting. The first two digits (hour) on the LCD will blink. Use
the UP or DOWN button to set the
hour
that you’d like your recycling timer
to come ‘ON’. Press the Enter/Reset button to lock in the new setting. Next
the middle two digits (minutes) will blink. Use the UP or DOWN button to set
the
minute
that you’d like your recycling timer to come ‘ON’. Press the En-
ter/Reset button to lock in the new setting. Next the last two digits (seconds)
will blink. Use the UP or DOWN button to set the
second
that you’d like your
recycling timer to come ‘ON’. Press the Enter/Reset button to lock in the
new setting. Finally, the AM/PM will blink. Use the UP or DOWN button to set
AM
or
PM
. Press the Enter/Reset button to lock in the new setting.
• Recycling Timer ‘OFF’ Time – Press the Recycling Timer ‘OFF’ Time button.
The first two digits (hour) on the LCD will blink. Use the UP or DOWN button
to set the
hour
that you’d like your recycling timer to go ‘OFF’. Press the
Enter/Reset button to lock in the new setting. Next the middle two digits
(minutes) will blink. Use the UP or DOWN button to set the
minute
that you’d
like your recycling timer to go ‘OFF’. Press the Enter/Reset button to lock in
the new setting. Next the last two digits (seconds) will blink. Use the UP or
DOWN button to set the
second
that you’d like your recycling timer to go
‘OFF’. Press the Enter/Reset button to lock in the new setting. Finally, the
AM/PM will blink. Use the UP or DOWN button to set
AM
or
PM
. Press the
Enter/Reset button to lock in the new setting.
• Override Recycle Timer – Press the Override Recycle Timer button for ap-
proximately 2 seconds. The Recycling Timer Output will be activated and the
recycling timer will begin counting down the recycle ON TIME. After the timer
counts all the way down, the recycle timer will return to current saved set-
tings and resume normal operation. To end the test early, press the Override
Recycle Timer button again.
• Day/Night/24 Hour – Press the hold the Day/Night/24 Hour button for
approximately 2 seconds to program the Recycling Timer Output to operate
during the
day
, at
night
or continuously for
24 Hours
. The current setting will
be displayed. Press the UP and DOWN buttons to scroll through the Day /
Night / 24 Hour Settings. Press Enter/Reset to select the new setting.
NOTE:
There is no built-in photocell on the Hades
™
2. The recycling timer relies
on the Turn Lights ON TIME & Turn Lights OFF TIME to tell the Hades
™
2 when it is Day or Night.
• Recycle Timer Mode – Press the Recycle Timer Mode button to select either
Stop mode or Cont (Continuous) mode. This mode will determine whether
the recycle timer stops or continues when a power interruption occurs. The
default mode is Stop from the factory. The recycling timer will Stop counting
if the power to the timer is interrupted. In the Cont (continue) mode, the recy-
cling ‘ON’ time will continue to count down when the power to the Hades
™
2 is interrupted. This countdown sequence will continue until the power is
restored so that no time is lost during the power interruption period. Change
settings using the UP and DOWN keys. Press the Enter/Reset button to lock
in the new setting.
• Press For Temp – Press the Press For Temp button to display the current
room temperature. To switch the temperature reading from Celsius to Fahr-
