manualshive.com logo in svg

TIL TDFM-7000, Инструкция по установке и эксплуатации


Поделиться
Скачать
background image

TECHNISONIC INDUSTRIES LIMITED 

www.til.ca 

 

 

TDFM-7000 Installation & Operating Instructions 

TiL 05RE375 Rev n/c Issue 13

v 

 

TABLE OF CONTENTS

 

SECTION 

TITLE 

 PAGE

 

 SECTION 1 

GENERAL DESCRIPTION 

1.1 INTRODUCTION ................................................................................................    1-1 
1.2 DESCRIPTION ...................................................................................................    1-1 
1.3 

MODEL VARIATION ...........................................................................................    1-1 

1.4 TECHNICAL 

CHARACTERISTICS .........................................................................    1-3 

 

 SECTION 2 

OPERATING INSTRUCTIONS 

2.1 GENERAL 

.........................................................................................................    2-1 

2.2 FRONT 

PANEL  ..................................................................................................    2-1 

2.3 POWER 

SWITCH  ...............................................................................................    2-2 

2.4 KNOB 

..............................................................................................................    2-2 

2.5 

SOFT KEYS AND HOME .....................................................................................    2-2 

2.6 BAND 

KEY 

.......................................................................................................    2-3 

2.7 FUNC 

KEY 

........................................................................................................    2-3 

2.8 

F1 – F4 KEYS ...................................................................................................    2-3 

2.9 

MUP(4) AND MDN(7) KEYS (Memory Up and Down Keys)  ......................................    2-5 

2.10 UP(5) 

AND 

DN(8) KEYS  .....................................................................................    2-5 

2.11  BRT(6) AND DIM(9) KEYS  ..................................................................................    2-5 
2.12  ESW(0) KEY (Ergo Switch)  .................................................................................    2-5 
2.13  TSW (*) KEY ....................................................................................................    2-5 
2.14 DISPLAY 

..........................................................................................................    2-5 

2.15 GENERAL 

OPERATION .......................................................................................    2-6 

2.16 CUSTOMER 

PROGRAMMING 

SOFTWARE (CPS™) ..................................................    2-6 

2.17 CONFIGURATION MENU  ....................................................................................  2-11 
2.18 KEYLOADING MODE  .........................................................................................  2-12 
2.19  FLASH UPGRADE MODE  ....................................................................................  2-12 
2.20  FRONT PANEL PROGRAMMING (FPP) MODE - OPTIONAL  ......................................  2-13 
2.21 AUTOTEST 

CABABILITY  ....................................................................................  2-15 

 

 SECTION 3 

INSTALLATION INSTRUCTIONS 

3.1 GENERAL 

.........................................................................................................    3-1 

3.2 EQUIPMENT 

PACKING LOG  ................................................................................    3-1 

3.3 INSTALLATION  .................................................................................................    3-1 
3.4 

INSTALLATION KIT - CONTENTS ........................................................................    3-1 

3.5 ANTENNA 

INSTALLATION .................................................................................    3-1 

3.6 

INSTALLATION - PIN LOCATIONS AND CONNECTIONS .........................................    3-3 

3.7 

INSTALLATION - WIRING INSTRUCTIONS  ............................................................    3-4 

3.8 

MAIN GROUND – PINS 1 AND 14  .......................................................................    3-4 

3.9 

MAIN POWER + 28VDC – PINS 2 AND 15  ..........................................................    3-4 

3.10  MIC 1, 2, 3, 4 and COMBINED – J1 PINS 3, 6, 9 and J2 PIN 6; J2 PIN 7 (COMB) .....    3-4 
3.11  AUDIO 1, 2, 3, 4 and COMBINED – J1 PINS 4, 7, 10 and J2 PIN 5; J2 PIN 2 (COMB     3-4 
3.12  PTT 1, 2, 3, 4 and COMBINED – J1 PINS 5, 8, 11 and J2 PINS 3; J2 PIN 4 (COMB)  .    3-4 
3.13  TX DATA AND RX DATA – J1 PINS 12 AND 13 ...................................................    3-4 
3.14  CHANNEL UP AND CHANNEL DOWN – J1 PINS 16 AND 17  ..................................    3-4 
3.15  LH DATA, SB9600 BUSY, OPTB+, CTS OUT, BOOT DIN, RTSBIN AND RS232DIN – 
 

J1 PINS 18 THROUGH 24 ...................................................................................    3-4 

3.16 PANEL 

BACKLIGHTING 

– J1 PIN 25  ....................................................................    3-5 

Содержание TDFM-7000

























































Отзывы:

Нет отзывов

Похожие инструкции для TDFM-7000

S+S Regeltechnik THERMASGARD TM 65 Operating Instructions Manual preview
THERMASGARD TM 65
Бренд: S+S Regeltechnik Страницы: 16
S+S Regeltechnik PREMASGARD 211 Series Operating Instructions, Mounting & Installation preview
PREMASGARD 211 Series
Бренд: S+S Regeltechnik Страницы: 11
Vanderbilt SPCW120 Manual preview
SPCW120
Бренд: Vanderbilt Страницы: 5
Radio Shack HTX-212 Owner'S Manual preview
HTX-212
Бренд: Radio Shack Страницы: 44
SpeakerCraft SC-WIR-TX Installation Manual preview
SC-WIR-TX
Бренд: SpeakerCraft Страницы: 5
Icom IC-F3161DS Instruction Manual preview
IC-F3161DS
Бренд: Icom Страницы: 40
Horizon Hobby RMTTI01 User Manual preview
RMTTI01
Бренд: Horizon Hobby Страницы: 23
Bang & Olufsen Playmaker Installation Manual preview
Playmaker
Бренд: Bang & Olufsen Страницы: 14
Intermatic RC613 Installation, Operation & Service Manual preview
RC613
Бренд: Intermatic Страницы: 2
Inovonics FA223S-LTH Installation Instructions preview
FA223S-LTH
Бренд: Inovonics Страницы: 2
Zenith H2226R Service Manual preview
H2226R
Бренд: Zenith Страницы: 55
Perle SPEED Series User Manual preview
SPEED Series
Бренд: Perle Страницы: 122
Phonic Ear EasyListener2 230R User Manual preview
EasyListener2 230R
Бренд: Phonic Ear Страницы: 53
M-system 10TG Instruction Manual preview
10TG
Бренд: M-system Страницы: 2
Jensen CDR171 Installation & Owner'S Manual preview
CDR171
Бренд: Jensen Страницы: 28
Marantz SR5005 (French) Manuel D'Utilisation preview
SR5005
Бренд: Marantz Страницы: 91
S+S Regeltechnik PREMASGARD SHD652 Operating Instructions, Mounting & Installation preview
PREMASGARD SHD652
Бренд: S+S Regeltechnik Страницы: 16
Safeguard Supply ERA-PBDCR Owner'S Manual preview
ERA-PBDCR
Бренд: Safeguard Supply Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды