TIL TDFM-7000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 56

background image

TECHNISONIC INDUSTRIES LIMITED

www.til.ca

TDFM-7000 Installation & Operating Instructions

TiL 05RE375 Rev n/c Issue 13

2-8

Programming Cables for units with Type I modules

To make any changes to the programming in the radio, CPS™ software must be used. There
is no provision in the Type I radio to allow the user to change frequencies, zones, talk
groups, etc. from the front panel.

“ASTRO Saber & XTS 3000”CPS™ software can be purchased from Motorola Customer
Service (see following page). A Motorola Radio Interface Box (RIB) is required to connect
the computer to the TDFM-7000 if Type I modules are installed. Each band in the TDFM-
7000 is considered a Type I (XTS-3000) portable by the CPS™ software. To program a band
in the transceiver, it must be selected by pressing the BAND key before running the CPS™.
Follow the instructions supplied with the CPS™ and RIB. The radio cable supplied with the
RIB will not connect to the TDFM-7000, therefore you will need to purchase the Type I
programming cable, P/N 037347-1.

The CPS Programming software must be purchased from Motorola on Line (MOL).
For instructions on ordering Motorola parts and CPS software see TIB TIBFM 12-01 REV E.
This document can be found in Appendix A or is available on the Technisonic Web site at
www.til.ca.
Follow the link for TDFM 7000 and click in the Link for “CPS Programming software/Cables
ordering Guide”. Refer to the section for Type I Modules.

P/N RVN4182

CPS Programming Software,

Note:

Latest revision will be provided.

P/N RLN10150

Smart RIB Interface Box

P/N 0180202E27

Smart RIB AC PWR PAC 110V

P/N 3080390B48

Computer RIB Cable

The XTS-3000 and XTS-5000 are products of Motorola, Inc.
The KVL-3000 is a product of Motorola, Inc.

A Technisonic Type I programming cable P/N037347-1 is also required and available from
Technisonic. If encryption keys need to be loaded via a KVL-3000+, keyloader cable P/N
037348-1 may be also be obtained from Technisonic. This keyloader cable will plug into the
front connector of the TDFM-7000 transceiver and will work with Type I or Type II modules.

To use the programming connector on the front of the TDFM-7000 transceiver, which is
preferable when the unit is installed in an aircraft, use the following:

P/N 037347-1

Download/Programming Cable that mates with RIB interface Box to
program TDFM-7000 units employing Type I modules.

P/N

037348-1 Encryption Keyload Cable that mates with Motorola KVL-3000

Keyloader. Same P/N for Type I or Type II modules.

P/N 013524-1

Alternate programming cable that mates with Rear DB 25 connector.

«
...
18
19
20
21
22
...
»

Содержание TDFM-7000

























































Отзывы:

Нет отзывов

Похожие инструкции для TDFM-7000

Бренд: QUNDIS Страницы: 8

Бренд: Radionics Страницы: 73

Бренд: RadioMaster Страницы: 3

Бренд: Eaton Страницы: 2

Бренд: Mammut Страницы: 40

Бренд: Akai Страницы: 33

Бренд: Alinco Страницы: 48

6.1 Channel AV Reciever LR-6500

Бренд: Luxman Страницы: 36

ATS-909X - WORLD BAND RADIOS

Бренд: Sangean Страницы: 11

Бренд: Net Safety Страницы: 50

Бренд: Sennheiser Страницы: 6

Бренд: Teleco Страницы: 2

Бренд: Omron Страницы: 104

Бренд: JTS Страницы: 24

Бренд: tams elektronik Страницы: 12

Бренд: ZIEHL-ABEGG Страницы: 12

Бренд: Harman Kardon Страницы: 16

NETWORX NX-548E

Бренд: GE Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды