background image

466-2225B   July 2006

Copyright © 2006, GE Security Inc.

NetworX NX-548E Receiver

Installation Instructions

Contents

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Internal mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

External mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Wiring

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DIP switch settings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power up

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Testing and troubleshooting

 . . . . . . . . . . . . . . . . . . . . . . . . 6

Programming settings table

 . . . . . . . . . . . . . . . . . . . . . . . . 7

Supported devices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Specifications

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction

The NX-548E Receiver adds wireless capabilities to the 
NetworX line of control panels. Adding a receiver makes these 
control panels compatible with NX wireless transmitters.
Only three wire connections are required for power and commu-
nication to the control panel.

Internal mounting

For internal mounting, mount the receiver inside the control 
panel enclosure. Use the following installation guidelines:

• Leave at least 10 in. (25 cm) above the control panel for the 

receiver’s antennas.

• Avoid areas that expose the receiver to moisture.
• Avoid areas with excessive metal or electrical wiring, 

including furnaces and utility rooms.

To mount the receiver, do the following:
1.

Remove the appropriate knockouts on the top of the control 
panel enclosure for the antenna shrouds.

2.

Assemble the antenna shrouds and fit the black O-rings to 
the bottom of each shroud.

3.

Insert the shrouds into the knockout holes (

Figure 1

).

Figure 1.

Installing the antenna shrouds 

4.

Use the mounting screw provided to loosely install the edge 
guide standoff in the lower mounting hole in the appropriate 
space to the left of the control panel (

Figure 2

). Do not 

tighten the mounting screw down at this time.

Figure 2.

Installing the edge guide standoff

 

5.

Slide the printed circuit board into the antennae shroud 
slots, after inserting wires into antennae shrouds (

Figure 3

).

Figure 3.

Anntennae shrouds

WA

WARNING:   To avoid possible equipment damage 

or personal injury, remove power from 
the control panel before making any 
wiring connections to the receiver.

Antenna shroud

O-ring

Knockout hole

Enclosure top

CAUTION

You must be free of static electricity before 
handling circuit boards. Touch a bare metal 
surface or wear a grounding strap to 
discharge yourself.

Mounting screw

Edge guide standoff

Circuit

Antennae

Enclosure

   shrouds

board

Содержание NETWORX NX-548E













Отзывы: