TIL TDFM-7000 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

background image

TECHNISONIC INDUSTRIES LIMITED

www.til.ca

TDFM-7000 Installation & Operating Instructions

TiL 05RE375 Rev n/c Issue 13

3-19

3.19 TDFM-7000/7300 SOFTWARE OPTION

FOR CONTROL OF LATITUDE SATELLITE GATEWAY S200-SG11

3.19.1 GENERAL

The TDFM-7000/7300 software option for control of the Latitude satellite gateway S200-
SG11 allows the TDFM-7000 to act as a controller for the above system replacing the usual
controller thereby saving space and weight in the aircraft and providing a larger display and
keypad. The satellite gateway provides three main functions:

1.

Satellite Phone capability

2.

Outgoing Text Messages to e-mail addresses

3.

Automated GPS Position Reporting

The transceiver controls the satellite gateway system through the RS-232 port on the back
of the unit. All audio and keying is connected separately to a free position on the aircraft
audio panel. The TDFM-7000 acts as a controller only. This option precludes the use of an
RC-7000 at this time. This option is identified as Mod 4 on the modification record label.

3.19.2 INSTALLATION

Connect the TDFM-7000 and the S200-SG11 as shown in figures 3.3. See the S200-SG11
installation instructions for details.

FIGURE 3.3

TDFM-7000 and S200-SG11 Wiring Diagram

«
...
45
46
47
48
49
...
»

Содержание TDFM-7000

























































Отзывы:

Нет отзывов

Похожие инструкции для TDFM-7000

Бренд: Nautel Страницы: 105

Бренд: Samyung ENC Страницы: 64

Бренд: Yaesu Страницы: 40

Бренд: Yaesu Страницы: 35

Бренд: Yaesu Страницы: 39

Бренд: Yaesu Страницы: 2

Бренд: Yaesu Страницы: 15

Бренд: Yaesu Страницы: 44

Бренд: M-system Страницы: 2

Бренд: Onkyo Страницы: 20

Бренд: IDT Страницы: 25

Бренд: HobbyKing Страницы: 2

Бренд: Gear4 Страницы: 104

Бренд: IROX Страницы: 2

Бренд: TT Micro Страницы: 17

SoundPlus Infrared Receiver WIR RX12-4

Бренд: Williams Sound Страницы: 2

Бренд: Lumantek Страницы: 16

Control Medi Standard

Бренд: Abilia Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды