Tiger TIGERFLEX Copia Скачать руководство пользователя

Страница: 29 / 32

Please retain instructions for future reference

Step 21:

FELTING THE ROOF

(MEASURE AND CUT BEFORE INSTALLING THE FELT)

• Roll felt out onto a clean flat surface 30 minutes before you need it so it has a chance to flatten out.

• Measure length of roof and allow 75mm overhang at each end. Cut each strip of felt to size.
Use a straight edge to guide cutting.

• Roll cut felt piece along low side of roof, Section 1, leaving sufficient overhang to fold down onto roof edge.

NOTE: DO NOT FOLD UNDERNEATH ROOF.

(Detail V1 & V2)

• Once felt is rolled out, fix to roof using CN13 at approx. 100mm intervals.

(Detail V3)

Ensure the felt is tight, then

secure the top side of felt using CN13 at approx. 100mm intervals.

• Repeat for remaining felt, working from the low side of roof to the high side, overlapping the felt by 75mm
until the roof is fully covered.

• Fold the overhanging felt at ends under roof panel and tack in place.

C13

CORRECT

FELT

INCORRECT

FELT

Содержание TIGERFLEX Copia

































Результаты поиска

Содержание TIGERFLEX Copia

Отзывы:

Похожие инструкции для TIGERFLEX Copia

Бренды по названию

Популярные бренды

Tiger TIGERFLEX Copia, Общие инструкции по сборке

Результаты поиска

Содержание TIGERFLEX Copia

Отзывы:

Похожие инструкции для TIGERFLEX Copia

Бренды по названию

Популярные бренды