Tiger BENGAL JD51 M Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 240

background image

OPERATION

Boom

Operation Section 3-29

©2013 Alamo Group Inc.

OPERA

TION

Transport only at speeds where you can maintain control of the
equipment. Serious accidents and injuries can result from operating this
equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering
and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for
you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly
to determine the stopping characteristics of the Tractor and Implement. As you increase
the speed of the Tractor the stopping distance increases. Determine the maximum
transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after
you determine that the equipment can be operated at a higher speed. Use extreme care
and reduce your speed when turning sharply to prevent the tractor and implement from
turning over. Determine the maximum turning speed for you and this equipment before
operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control
the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes
or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance
increases: use extreme care and reduce your speed.   When operating in traffic always use
the Tractor’s flashing warning lights and reduce your speed.   Be aware of traffic around you
and watch out for the other guy.

(SG-19)

8.1 Starting the Tractor

The procedure to start the tractor is model specific.
Refer to the tractor operator’s manual for starting
procedures for your particular tractor. Consult an
authorized dealer if the starting procedure is
unclear. Ensure the 3-point control lever is in the
lowered position and the PTO is disengaged before
starting the tractor.

OPS-U-0033

«
...
79
80
81
82
83
...
»

Содержание BENGAL JD51 M Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BENGAL JD51 M Series

Бренд: Veris Industries Страницы: 2

Бренд: Mahindra Страницы: 120

Бренд: Manfrotto Страницы: 2

Бренд: Campbell Страницы: 46

Бренд: V-ZUG Страницы: 12

Бренд: Garland Страницы: 36

Бренд: 4MOMS Страницы: 20

Micropulse BTL5 Series

Бренд: Balluff Страницы: 16

Бренд: Wahoo Страницы: 2

Бренд: Yamaha Страницы: 33

Бренд: Yamaha Страницы: 17

Бренд: Xtool Страницы: 16

Бренд: GATmatic Страницы: 13

Бренд: Ikan Страницы: 2

Бренд: Takex Страницы: 11

Бренд: GF Страницы: 8

Бренд: SpectraLink Страницы: 51

Бренд: Trailboss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды