Tiger BENGAL JD51 M Series Скачать руководство пользователя | Manualshive

Страница: 54 / 240

background image

OPERATION

Boom

Operation Section 3-2

©2013 Alamo Group Inc.

OPERA

T

ION

TIGER BOOM MOWER

OPERATING INSTRUCTIONS

Tiger Booms are manufactured with quality material by skilled workers. The Boom is designed to attach to a
tractor and operate various heads for a wide range of vegetative maintenance applications. The boom and
heads are equipped with safety warning decals, protective deflectors, shields, and other safety features to
provide operator and passerby protection, however, no shielding is 100% accurate. ALL safety equipment and
safety warning decals must be maintained on the unit in good operational condition at all times.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every
reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the
boom unit, tractor or a thrown object. Do not operate the boom and attached head if bystanders, passersby,
pets or livestock are within 300 feet of the unit.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate operators to the safe and
proper use of the boom and attached head. Pictures contained in this section are intended to be used as a
visual aid to assist in explaining the operation of a Boom and are not specific to a Boom. Some pictures may
show shields removed to enhance visual clarity. NEVER operate the boom unit without all safety equipment in
place and in good operational condition. The operator must be familiar with the boom unit and tractor
operation and all safety practices before beginning operation. Proper operation, as detailed in this manual, will
help ensure years of safe and satisfactory use of the Boom

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS
MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND
IMPLEMENT.

If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation. Pay close attention to all safety signs and safety messages contained in this manual and
those affixed to the implement and tractor.

(OPS-U- 0001)

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or
death may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad.

(SG-3)

«
...
52
53
54
55
56
...
»

Содержание BENGAL JD51 M Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BENGAL JD51 M Series

Бренд: UFESA Страницы: 27

Бренд: LAZER Страницы: 13

Бренд: Latento Страницы: 60

Бренд: Easy Quick Страницы: 11

Бренд: Radio Shack Страницы: 2

Бренд: Campbell Страницы: 46

Бренд: V-ZUG Страницы: 12

Бренд: Makita Страницы: 64

Бренд: Datalogic Страницы: 248

Бренд: KDS Страницы: 72

Бренд: Taylor-Dunn Страницы: 60

Бренд: Fabbri Страницы: 4

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды