Tiger BENGAL JD51 M Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 240

background image

ASSEMBLY

Assembly Section 2-2

Before attempting to mount your Tiger mower, it is important

to read and understand all of the safety messages in the Safety
Section of this manual.

Check complete shipment list against the packing list to make sure there are no

shortages. Make certain the tractor model is the appropriate one for the mower received!

Always use a floor jack, hoist or fork lift to lift and raise heavy parts.

Read and understand the entire Assembly Section instructions before attempting to mount

your Tiger mower. Refer to the Parts Section of this manual for detailed illustrations to locate all
parts.

(ASM-C-0001)

TRACTOR PREPARATION

A.

Remove right and left hand steps.

B.

Disconnect battery cables from both batteries.

C.

Remove engine side panels, or raise hood to access front pulley.

D.

Remove plugs from tractor casting where mainframe and pump mount will be attached.

E.

Remove any front weights and weight supports.

F.

Raise the tractor onto jack-stands and remove the right and left rear wheels.

(ASM-JD-0001)

ADJUSTING REAR WHEELS

Raise rear of tractor onto jack-stands.

Follow the instructions in the tractor owner’s

manual for adjusting tires and rims

. The back wheels MUST be adjusted to the widest

setting. NOTE: This may require switching the wheels to opposite sides of tractor. Also take
note of any width restrictions when transporting by trailer. (For ease of installation, it is best to
leave the rear wheels removed during installation of the mower.)

(ASM-B-0001)

«
...
30
31
32
33
34
...
»

Содержание BENGAL JD51 M Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BENGAL JD51 M Series

Бренд: Iget Страницы: 7

Бренд: Abibird Страницы: 2

Бренд: Abicor Binzel Страницы: 20

Бренд: Garmin Страницы: 26

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 72

Бренд: Vauxhall Страницы: 2

Бренд: IBASE Technology Страницы: 100

Бренд: JUGS Страницы: 17

Бренд: LEGRAND Страницы: 2

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

Бренд: U.S. General Страницы: 4

Бренд: Pilz Страницы: 8

Бренд: Smith-Victor Страницы: 2

Бренд: Datavideo Страницы: 24

STEADYSTAND Cross Basic

Бренд: ACEBIKES Страницы: 6

Бренд: RADARchron Страницы: 2

Бренд: Ednet Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды