screen changes.
5. Scroll down to “units.” Hold both ▲ and ▲ arrows until the
word ENG flashes.
6. Let go of buttons and press ▲ one time. This will change
the text to MET (metric).
7. Press ▲ and ▲ buttons simultaneously until the flashing
stops to lock this setting. The screens will return to the
setup screen. Use the arrows to go back to the original menu.
TAPS² GAUGE indicates the position of the TAPS² plate;
refer to TAPS² Operation.)
Tigé Multifunction Gauge
Fuel (FUEL LEVEL) indicates the approximate amount of fuel
in the tank. These readings are only approximate and allow
an adequate margin of comfort.
Volt (Voltmeter) indicates electrical system operating
voltage DC. Normal operating voltage at 5000 RPM is 14.75
± 0.25 volts.
Temp (Engine Temperature) indicates the internal engine
coolant temperature in ºF. Normal operating temperature
is between 165-195º.
If gauge indicates temperature above 195º, shut
engine off immediately!
Oil (Engine Oil Pressure) indicates the pressure in PSI (lbs
per square inch) of the lubricating oil inside the engine.
Normal pressure is between 10-30 PSI at idle and 30-60 PSI
FEATURES
SECTION 3
3-15
at running speed.
CIRCUIT BREAKER PANEL
Standard and optional electrical equipment devices are
protected by circuit breakers located under the dash. The
pop breakers are labeled to identify the devices protected.
The MAIN PWR and AUX PWR breakers provide power to
their respective circuits. These PWR (power) breakers must
be on to power the circuits.
The pop breakers will trip (pop out) if overloaded and
cut power to the device. To reset, turn the device off (if
applicable) and push the breaker in. If the pop breaker
continues to pop out, see your Tigé Dealer. Your boat may
not be equipped with all of the devices, features or options.
Any accessory device added must not exceed the amperage
of the breaker or total circuit capacity.
A quick way to check if a pop breaker is tripped is to run
your fingers over breaker face to verify breaker is not
“popped” out.
FUSES
Fuses protect the circuit by limiting the amount of current
which can flow. If a fuse should “blow,” it usually indicates
a problem. See your Tigé Dealer.
Use only an identical replacement when replacing the fuse.
3-16
Содержание 2015 ASR
