Tianlong GeneRotex 96 Скачать руководство пользователя страница 12

Страница: 12 / 32

Chapter 3 Installation Requirements and Procedure

3.1 Installation Requirements

3.1.1 Environmental Requirements

a) Only applicable to an indoor environment with good ventilation, no corrosive gas and no strong magnetic field interference

b) Avoid using it in direct sunlight, keep it away from heaters, stoves and all other heat sources, and away from water sources,

such as pools and water pipes.

c) There shall be no electromagnetic field interference and no electrical equipment that generates vibration or high-frequency

waves around the instrument

d) When a single instrument is used, the distance between the ventilation hole around the instrument and the nearest object

shall not be less than 30cm. When multiple instruments are used at the same time, the distance between instruments shall be no

less than 80cm

e) Do not place the instrument on a soft cushion. Otherwise, the base will fall into the soft cushion and block the cooling fan

below the instrument

f) Do not place the instrument close to the wall or stack other objects behind the instrument to avoid affecting the heat

dissipation of the instrument

g) The instrument shall be placed at a location where the power cord is easily plugged and unplugged and away from people

passing by to prevent someone from tripping over the power cord

h) Operating ambient temperature:10

℃

~30

℃

;

i) The relative humidity shall be ≤80%;

3.1.2 Power Requirements

a) Working power supply requirements: Three-wire grounding power supply, voltage AC 220±10%, 50Hz/60Hz, 600VA; UPS

is recommended

b) The voltage between the neutral wire and the ground wire shall be less than 3V

3.2 Inspection before Installation

3.2.1 Environment and Power Inspection

Use a conforming hygrothermograph to measure the temperature and humidity in the operating room of the nucleic acid

Ｃｏｐｙｒｉｇｈｔ　＠Ｔｉａｎｌｏｎｇ　Ｓｃｉｅｎｃｅ

Содержание GeneRotex 96

































Результаты поиска

Содержание GeneRotex 96

Отзывы:

Бренды по названию

Популярные бренды

Tianlong GeneRotex 96, Руководство по обслуживанию

Результаты поиска

Содержание GeneRotex 96

Отзывы:

Бренды по названию

Популярные бренды