Thrane&Thrane TT-3026L easyTrack страница 55 Скачать руководство пользователя

Страница: 55 / 60

TT-3026L easyTrack Transceiver

Installation Manual

55/

AINTENANCE GUIDELINES

When properly installed the TT-3026L needs no maintenance.

After approximately 10 years an internal battery has to be

replaced, and the transceiver must be sent for service. Low

battery level will result in loss of configuration data in case the

unit is powered down.

7.1

ANDLING

RECAUTIONS



Do not expose the transceiver’s parting line (the blue

styling gasket) & connector to high-pressure water

jets.



Exposure of chemical containing alkalis may result in

physical degradation of the transceiver.



Do not expose the transceiver to acid curing silicone.



Avoid contact with solvents.

Do not paint the transceiver. If it is absolutely necessary to

paint the transceiver, ideally water-based paints or paint

system based on mild solvents should be selected.

Содержание TT-3026L easyTrack





























































Результаты поиска

Содержание TT-3026L easyTrack

Отзывы:

Похожие инструкции для TT-3026L easyTrack

Бренды по названию

Популярные бренды

Thrane&Thrane TT-3026L easyTrack, Руководство по установке

Результаты поиска

Содержание TT-3026L easyTrack

Отзывы:

Похожие инструкции для TT-3026L easyTrack

Бренды по названию

Популярные бренды