Thrane&Thrane TT-3026L easyTrack Скачать руководство пользователя

Страница: 51 / 60

TT-3026L easyTrack Transceiver

Installation Manual

51/

This bar has 5 steps from all green to all red, depending on

the quality of the satellite signal. Green: good signal quality.

Red: no signal.

PC connect

Green: easyMail has connected to easyTrack. Red: No

connection between easyMail and easyTrack

Please go on to the easyMail basic setup section, for a quick

guide to getting easyTrack and easyMail configured and

ready to use.

5.5

EASY

AIL BASIC SETUP

When starting easyMail for the first time, a few things need to

be configured:



Configure Mobile number.



Default LES and E-mail Service Provider for sending

messages.

Mobile number

Click Options



Configuration



Mobile number. The following

dialog is shown:

Type the Mobile number (9 digits) and click ‘Ok’.

The Mobile number should be updated:

Содержание TT-3026L easyTrack





























































Результаты поиска

Содержание TT-3026L easyTrack

Отзывы:

Похожие инструкции для TT-3026L easyTrack

Бренды по названию

Популярные бренды

Thrane&Thrane TT-3026L easyTrack, Руководство по установке

Результаты поиска

Содержание TT-3026L easyTrack

Отзывы:

Похожие инструкции для TT-3026L easyTrack

Бренды по названию

Популярные бренды