Thrane&Thrane TT-3026L easyTrack страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 60

background image

TT-3026L easyTrack Transceiver

Installation Manual

23/

60

4.1.1.3

A

DJUSTABLE

P

OLE

/R

AILING

M

OUNT

403026 Opt. 103 is an adjustable pole/railing mount shown in

Figure 9



Attach the pole mount to the transceiver using the 3

screws.



Mount the device to the pole in one of the 2 directions.



Connect the cable.

Figure 9 Vertical and Horizontal adjustable pole mount

4.1.2

A

NTENNA

M

OUNTING

C

ONDITIONS

When installing the TT-3026L easyTrack, find a location that is

as free from obstructions as possible. Also maintain a certain

distance to other antennas.

The antenna is designed to provide satellite coverage even

when the vehicle is tilted up to 15°. To maintain this coverage

the antenna should be free from obstructions in the area down

to 15° below the horizon (see Figure 10). Any compromise in

this recommendation could degrade performance.

«
...
21
22
23
24
25
...
»

Содержание TT-3026L easyTrack





























































Отзывы:

Нет отзывов

Похожие инструкции для TT-3026L easyTrack

Бренд: York Fitness Страницы: 34

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: C.M.O Страницы: 10

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: EarthQuake Страницы: 12

Бренд: Pari Страницы: 2

Бренд: Garmin Страницы: 2

Бренд: Maeda Страницы: 276

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Garden Treasures Страницы: 2

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 48

Бренд: Panasonic Страницы: 23

Бренд: Daekyung Страницы: 15

Бренд: Exmark Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды