manualshive.com logo in svg

THORLABS SC10, Руководство по эксплуатации, Страница: 8 / 12

Поделиться
Скачать
THORLABS SC10 Скачать руководство пользователя страница 8

 

SH05 Interface 

The interface to the SH05 Shutter is via a 6 pin HRS female connector. The pin descriptions are as follows: 
 

Pin Description 

1 

To Opto cathode -GND 

2   

To Shutter Coil  - 24V pulse 

            10V steady state (.4A max) 

3 

To-Shutter Coil  - GND (on) 

  Open Ckt (off) 

4 

To- Opto Anode (12V limited to 20mA) 

5 

To- Opto Emitter- GND 

6 

To- Opto Collector (2.5V) 

 

 

SHO5 Connector Rear Panel 

Operating From a Computer: 

 

Overview 
 

• 

The SC10 Shutter Controller is fully operational from a remote computer via and RS232 interface.

 

• 

Connection from the computer to the SC10 is made with a standard DB9 cable (supplied).

 

• 

The SC10 can be controlled using the SC10 Application Software provided with the unit.

 

• 

It can also be controlled directly using a command line interface and any Terminal 
Communications software such as HyperTerminal.

 

• 

And finally it can be configured and operated using National Instrument’s LabView

®

 or Lab 

Windows

®

  using the drivers supplied with the unit.

 

Application Software operation 

 
The SC10 comes with a CD-ROM containing application software to control the unit from a PC.  After installing 
the software (see software installation), apply power to the unit. Connect a 9 pin (DSUB) serial cable between the 
SC10 and the PC. To execute the SC10 standalone application select “Programs->Thorlabs->SC10” from the 
Start menu. 
 
The initial screen will appear as follows:

 

 

8654-D02  Rev. B  8/15/05 

Page 8 of 12 

Содержание SC10













Отзывы:

Нет отзывов