THORLABS SC10 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

THORLABS SC10 Скачать руководство пользователя страница 5

8654-D02 Rev. B 8/15/05

Page 5 of 12

Front Panel Keys and Indictors:

SELECT

- Selects the window or function to be operated on. The Main LCD display screen contains four

display windows, each is located in a quadrant of the display. The windows are

TIME OPEN

,

TIME CLOSED, MODE

, and

TRIGGER

. The

SELECT

key is used to move between the four

windows (quadrants) of the display. The active quadrant is indicated by the “

_

” (underscore) in

the quadrant. When the underscore “_” is present in the quadrant the contents of the quadrant
may be modified using the

◄►▲▼

keys.

ENABLE -

Enables operation the controller as per the programmed parameters. When the unit is enabled
the “ENABLED” indicator will illuminate. Pressing the

ENABLE

key while the unit is enabled will

disable the unit.

▲

-

Increments either numerically (digits) or steps up through the options in the active window.

▼

-

Decrements either numerically (digits) or steps down through the options in the active window.

◄

-

Moves the curser left in the active display.

►

-

Moves the curser right in the active display.

ENABLED -

Illuminates when the unit is active or waiting for a trigger event to executing the programmed
parameters.

SHUTTER -

Illuminates when the shutter is open or the output pulse is “active high”.

OPEN

OPERATION

Initial Set-up

Locate the unit on a dry, level working surface.

Make sure the

POWER

switch on the front of the unit is in the OFF position ( 0 ).

Plug the female end of the AC line cord provided into the AC Input Receptacle on the rear of the unit.
Plug the male end into a properly grounded AC socket.

Connect the SH05 cable to the connector on the rear of the unit.

Turning ON the Unit

Turn the Power Key lock switch clockwise to the ON position ( | ). The LCD screen will display a brief
message stating the model number and the firmware revision. After approximately 2 seconds this
message will scroll off of the screen and the “Main” LCD screen will appear.

The unit defaults to the “ MANUAL” mode on the initial power-up. Subsequent power-up conditions
will default to the set parameters when unit was last enabled.

Make sure that the Remote Interlock input is “closed”. See “Remote Interlock” below.

In the MANUAL mode the

ENABLE

keypad on the front panel will open and close the shutter. The

“SHUTTER OPEN” indicator will track the shutter status.

«
...
3
4
5
6
7
...
»

Содержание SC10













Отзывы:

Нет отзывов