THORLABS BBD101 Скачать руководство пользователя страница 68

Страница: 68 / 76

GetDCProfileModeParams

Gets the settings for the profile mode

GetDCJoystickParams

Gets the settings for the joystick max velocity and
acceleration

GetDCSettledCurrentLoopParams

Gets the Current servo loop PID parameter settings
applied when the unit is ‘settled’.

GetDCTriggerParams

Gets the present Trigger Mode settings.

GetDispMode

Gets the GUI display mode.

GetHomeParams

Gets the homing sequence parameters.

GetHomeParams_HomeVel

Gets the homing velocity parameter (returned by
value).

GetHomeParams_ZeroOffset

Gets the homing zero offset parameter (returned by
value).

GetHWCommsOK

Gets the hardware communications OK flag.

GetJogMode

Gets the jogging button operating modes.

GetJogMode_Mode

Get the jogging button operating mode (returned by
value).

GetJogMode_StopMode

Gets the jogging button stopping mode (returned by
value).

GetJogStepSize

Gets the jogging step size.

GetJogStepSize_StepSize

Gets the jogging step size (returned by value).

GetJogVelParams

Gets the jogging velocity profile parameters.

GetJogVelParams_Accn

Gets the jogging acceleration parameter (returned
by value).

GetJogVelParams_MaxVel

Gets the jogging maximum velocity parameter
(returned by value).

GetMotorParams

Gets the motor gearing parameters.

GetParentHWInfo ;

Gets the identification information of the host
controller.

GetPosition

Gets the current motor position.

GetPosition_Position

Gets the current motor position (returned by value).

GetPositionEx

Gets the current motor position.

GetPositionEx_UncalibPosition Gets the current uncalibrated motor position

(returned by value).

GetPositionOffset Gets

the motor position offset.

GetRelMoveDist Gets

the

relative move distance.

GetRelMoveDist_RelDist

Gets the relative move distance (returned by
reference).

Содержание BBD101













































































Результаты поиска

Содержание BBD101

Отзывы:

Похожие инструкции для BBD101

Бренды по названию

Популярные бренды

THORLABS BBD101, Руководство пользователя

Результаты поиска

Содержание BBD101

Отзывы:

Похожие инструкции для BBD101

Бренды по названию

Популярные бренды