THORLABS BBD101 Скачать руководство пользователя страница 18

Страница: 18 / 76

HA0237T Rev E Aug 2014

Chapter 3

3.6

Verifying Software Operation

3.6.1

Initial Setup

The APT Software should be installed (Section 3.1.) and the power up procedure
performed (Section 3.5.) before software operation can be verified.

1) Run the APTUser utility and check that the Graphical User Interface (GUI) panel

appears and is active.

Fig. 3.3 Gui panel showing jog and ident buttons

2) Click the ‘Ident’ button. The LED on the front panel of the controller flashes. This

is useful in multi-channel systems for identifying which driver unit is associated
with which GUI.

3) Click the jog buttons on the GUI panel and check that the motor or axis connected

to the controller moves. The position display for the associated GUI should
increment and decrement accordingly.

Follow the tutorial steps described in Chapter 4 for further verification of operation.

Note

The 'APT Config' utility can be used to set up simulated hardware

configurations and place the APT Server into simulator mode. In this way it

is possible to create any number and type of simulated (virtual) hardware

units in order to emulate a set of real hardware. This is a particularly useful

feature, designed as an aid to application program development and testing.

Any number of 'virtual' control units are combined to build a model of the

real system, which can then be used to test the application software offline.

If using real hardware, ensure that Simulator Mode is disabled. If using a

simulated setup, enable Simulator Mode and set up a ‘Simulated

Configuration’ - see Section 4.11. or the

APTConfig

helpfile for detailed

instructions.

Содержание BBD101













































































Результаты поиска

Содержание BBD101

Отзывы:

Похожие инструкции для BBD101

Бренды по названию

Популярные бренды

THORLABS BBD101, Руководство пользователя

Результаты поиска

Содержание BBD101

Отзывы:

Похожие инструкции для BBD101

Бренды по названию

Популярные бренды