THORLABS BBD101 Скачать руководство пользователя страница 69

Страница: 69 / 76

GetStageAxis

Gets the stage type information associated with the
motor under control.

GetStageAxisInfo Gets

the stage axis parameters.

GetStageAxisInfo_MaxPos

Gets the stage maximum position (returned by
value).

GetStageAxisInfo_MinPos

Gets the stage minimum position (returned by
value).

GetStatusBits_Bits

Gets the controller status bits encoded in 32 bit
integer (returned by value).

GetVelParamLimits

Gets the maximum velocity profile parameter limits.

GetVelParams

Gets the velocity profile parameters.

GetVelParams_Accn

Gets the move acceleration (returned by value).

GetVelParams_MaxVel

Gets the move maximum velocity (returned by
value).

Identify Identifies

the controller by flashing unit LEDs.

LLGetDigIPs

Gets digital input states encoded in 32 bit integer.

LLGetStatusBits

Gets the controller status bits encoded in 32 bit integer.

LLSetGetDigOPs

Sets or Gets the user digital output bits encoded in
32 bit integer.

LoadParamSet

Loads stored settings for specific controller.

MoveAbsolute

Initiates an absolute move.

MoveAbsoluteEnc

Initiates an absolute move with specified positions
for encoder equipped stages.

MoveAbsoluteEx

Initiates an absoloute move with specified positions.

MoveAbsoluteRot

Initiates an absolute move with specified positions
for rotary stages.

MoveHome

Initiates a homing sequence.

MoveJog

Initiates a jog move.

MoveRelative Initiates a relative move.

MoveRelativeEnc Initiates a relative move with specified distances for

encoder equipped stages.

MoveRelativeEx Initiates

relative move with specified distances.

MoveVelocity

Initiates a move at constant velocity with no end point.

SaveParamSet

Saves settings for a specific controller.

SetAbsMovePos

Sets the absolute move position.

SetBLashDist

Sets the backlash distance.

SetDCCurrentLoopParams

Sets the Current servo loop PID parameter values
applied when the unit is moving

Содержание BBD101













































































Результаты поиска

Содержание BBD101

Отзывы:

Бренды по названию

Популярные бренды

THORLABS BBD101, Руководство пользователя

Результаты поиска

Содержание BBD101

Отзывы:

Бренды по названию

Популярные бренды