2
GB
Method C – Programming by means
of code retrieval
Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the indicator lamp
blinks and then remains lit.
3. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
DVD
: DVD player, ,
SAT/
STB
: satellite receiver, cable, DVBT, ADSL,
AMP
:
AUDIO equipment and any other appliance.
4. Direct the remote control towards the set and try to
switch it off by pressing the key
G
.
5. If the set you want to control switches off, press
OK
to memorise the code.
6. Should the set not switch off, press key
G
as many
times as required (up to 200 times), until the
set switches off. Between two key presses, leave
enough time for the key corresponding to the
indicator lamp to light up again (about 1 second).
Proceeding this way will enable you to see whether
the set responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press
OK
to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page
3
.
Try out other remote control keys to find out the range
of functions you can control. If you think that not all
of the keys are active, repeat the procedure of this
programming method to find out the code supporting a
wider range of features.
Method D – Automatic
code search
With this method, the remote control scrolls through
the full code list by sending an IR signal to the set to be
controlled remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it on
manually.
2. Hold down the
SETUP
key until the indicator lamp
blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. Release the
SETUP
key.
4. Press the key corresponding to the type of
equipment (for example
TV
).
5. Press the
Prog
+ or standby
G
or
B
(
DVD
only)
key. After a few seconds, the remote control begins
to scroll through the whole code list included in the
library (at a rate of roughly 1 code per second).
Press the
Prog
+ key once again to slow down
the test speed (1 code every 3 seconds). As soon
as the set changes channels, you must press
OK
to save the code and stop the remote control
scrolling through the list. If you do not react quickly
enough, you can go back to the previous code by
pressing
Prog
- or
E
(
DVD
only) as many times
as necessary (you can go forward by pressing
G
,
Prog
+ or
B
(
DVD
only) if you have gone back
too far). As soon as the set responds again, press
OK
to save the code.
Method E – Programming for control of a
COMBO (combined TV- TV/DVD, DVD, … set)
Depending on the COMBO group (TV/ DVD, etc.)
and the make, you will be required to enter a single
code for both devices in the COMBO, or to enter two
codes, one code per device. Consult the separate list
to discover this.
Before you start programming, you must find the
subcode or code of the subset to be controlled
(television or video recorder, ...). Refer to the list
supplied with this user manual (see page subcodes
or codes).
1. Switch on the COMBO you want to control.
2. Hold the
SETUP
key down until the indicator lamp
blinks and then remains lit.
3. Press the key of the first device to control, and then
follow one of the programming methods A, B, C or
D previously described.
4. If a second code programming is required, then
repeat steps 2 and 3 above.
How to retrieve
a programmed code
It may be useful to retrieve the code programmed in
the remote control.
1. Hold down the
SETUP
key until the indicator lamp
blinks and then remains lit.
2. Press the key that corresponds to the type of
equipment you want to find the code:
TV
: television set,
DVD
: DVD player, ,
SAT/
STB
: satellite receiver, cable, DVBT, ADSL,
AMP
:
AUDIO equipment and any other appliance.
3. Press the
SETUP
key briefly, so that the indicator
lamp blinks once.
4. Press the numbered keys in ascending order (0 to
9) until the indicator lamp blinks once.
5. The number that caused the indicator lamp to blink
is the first of the four numbers that make up your
code. Make a note of it below.
6. Repeat step 4 to find out the other numbers of the
code.
7. When the fourth number has been found, the
indicator lamp goes out.
Method B – 4-digit codes
programming
Before you start programming, you must find the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the
SETUP
key until the indicator lamp
blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
DVD
: DVD player, ,
SAT/
STB
: satellite receiver, cable, DVBT, ADSL,
AMP
:
AUDIO equipment and any other appliance.
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example: 0166 for a Thomson TV).
5. Direct the remote control towards the set and try to
switch it off by pressing the key
G
.
6. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the
set by pressing key
G
once. Repeat this procedure
by trying out each of the 4-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands. Check your remote control for
proper functioning by performing the test described
on page
3
.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands. Check your remote control for
proper functioning by performing the test described
on page
3
.
Содержание ROC4411
Страница 2: ......
Страница 3: ...ROC4411 00131898 1 3 15 5 7 9 11 13 17 19 2 4 18 6 8 12 14 20 21 AAA 10 16 ...
Страница 73: ...69 ...