THM Carbones Clavicula SE Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

THM Carbones Clavicula SE Скачать руководство пользователя страница 27

LOREM

T H M

C L A V I C U L A S E

27

INSTALL

Installing the pedals

Pedals are manufactured with Right-hand thread for Right-hand pedals (drive side) and
Left-hand thread for Left-hand pedals.

It is essential not to confuse the RH and LH pedal!

-

Follow the instructions of the pedal manufacturer

-

We highly recommend to apply grease on the pedal threads

Risk of damage to the carbon structure around the pedal threads.
-

Do not exceed the maximum tightening torque for the pedals prescribed by THM
max.

20 Nm (177 lbf·in)

!

Finish touch

-

Check the position and adjustment of the front derailleur as well as the chain line.

-

Readjust the front derailleur if required.

Risk of accident caused by a malfunctioning crank system due to loose screw

connections.

-

Check the required tightening torque of all screw connections after the first 100 km

–

retighten the connections if necessary. Repeat this check every 2500km!

Apply fresh thread lock if necessary.

Risk of accident caused by a malfunctioning crank due to wear.

-

Do not continue to use your Clavicula component if the Clavicula lettering is
abraded at one or more points (wear indicator).

Please  note  that  if  you  use  overshoes,  or  if  there  is  an  extremely  small  clearance
between the brake shoe and crank, it will cause the crank surface to wear. This level of
wear is increased significantly if the bike is used frequently in wet and dirty conditions!
You  can  prevent  this  wear  by  sticking  an  appropriate  protective  film  (Lizard  Skins  or
other  similar film) over the  areas that are  susceptible  to wear. Check these areas for
wear at regular intervals!

INFO

WARNING

WARNING

INFO

«
...
25
26
27
28
29
...
»

Содержание Clavicula SE









































Отзывы:

Нет отзывов