THM Carbones Clavicula SE Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 40

THM Carbones Clavicula SE Скачать руководство пользователя страница 20

LOREM

T H M

C L A V I C U L A S E

20

INSTALL

BB30 / PressFit 30 / BBrightTM PressFit

For BB30, PressFit 30 and BBright

TM

PressFit bottom brackets:

The long bearing cup with internal thread

is always located on the drive side.

The short bearing cup with external thread is always located on the non-drive side.

BB30 / PressFit 30

-

Apply grease to the threads
and all fits.

-

Insert the long bearing cup

(2)

or

(4)

by hand as far as

possible into the drive-side
of

the

bottom

bracket

housing.

-

Screw the short bearing cup

(3)

or

(5)

by hand as far as

possible into the right-hand
bearing

cup

using

a

clockwise

rotation.

-

Make  sure  that  both  bearing
cups  are  located  centrally  in
front  of  the  bottom  bracket
housing.

-

Use

the

THM

Bottom

bracket tool ½ “

(1)

torque

wrench to apply 40 Nm

-

For PressFit 30 place the
sealings

BBright PressFit

TM

INFO

«
...
18
19
20
21
22
...
»

Содержание Clavicula SE









































Отзывы:

Нет отзывов