Think 3D STORMBEE S20 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 102

Think 3D STORMBEE S20 Скачать руководство пользователя страница 44

STORMBEE User Manual

–

Think 3D BVBA

Version N°1.1, last modified 30/09/2018

30

8.

Press on the small map in the bottom corner to switch between the “Google Maps” window

and the camera feed window. The Google Maps (satellite view) window will maximize, and you
should visually verify that STORMBEE

’s location is correct.

9.

Verify the DJI A3 LED module is blinking green.

10.

Use the laser range finder binocular to measure the height of the relevant obstacles within or
close by your mission area.

11.

Check the altitude set for the Return-To-Home (RTH) failsafe mode. Ensure that altitude set is
always at least 10m (30ft) higher than the highest structure in your vicinity.

12.

Ensure that the Lightbridge 2 remote controller is in the correct flight control mode! Pilots can
choose between different flight control modes for which the pitch, roll, yaw and throttle stick
functions are switched around across the two control sticks. The default flight controls mode

is “Mode 2”.

WARNING!!

Accidentally trying to take-off with the wrong flight control mode will very likely result
in a crash!

13.

Remove the foam mirror protection piece.

14.

Go to STORMBEE and power on the GNSS avionics by pressing the large button with the power

symbol

on it. The button will light up green and the GNSS avionics will boot up. This will

take several minutes. In addition, the FARO Focus scanner will now also receive power from
the flight batteries. After a few minutes, the GNSS avionics will start to find the current GPS-
location of the GPS modules attached at each end of the long carbon arms at the front and
back of the STORMBEE. The searching is indicated by the GNSS LED module blinking first
red/yellow and then green. When the GNSS LED module is blinking green for some time, the
GNSS GPS location is of sufficient quality for take-off (but not for the mission itself, see note
below).

«
...
42
43
44
45
46
...
»

Содержание STORMBEE S20







































































































Отзывы:

Нет отзывов