background image

 

pg. 4

1

1

1

1

1

INTRODUCTION

INTRODUCTION

INTRODUCTION

INTRODUCTION

INTRODUCTION

1.1

1.1

1.1

1.1

1.1

GENERAL GUIDELINES

GENERAL GUIDELINES

GENERAL GUIDELINES

GENERAL GUIDELINES

GENERAL GUIDELINES

This installation, use and maintenance guide is an integral and essential part of the product and must be kept by the user. Before commencing with
the installation, use and maintenance of the product, carefully read all the instructions contained in this booklet. At the time of installation of the
appliance all local regulations, including those that refer to national and European regulations, must be observed. The Manufacturer recommends
carrying out all the maintenance operations described in this manual.
This appliance must only be used as intended by the manufacturer. Any other use is considered incorrect and therefore hazardous; consequently,
the user shall be totally liable for the product if used improperly. Installation, maintenance and repairs must be carried out by personnel with
professional qualifications and in compliance with current regulatory standards and in accordance with the instructions of the manufacturer of
the appliance. Use only original spare parts.
Incorrect installation or poor maintenance could injure or damage people, animals or things; in this case the manufacturer shall be relieved of all
responsibility. Before commencing any cleaning or maintenance operation ensure that the appliance has been disconnected from the mains
power supply by means of the main system switch or some other disconnecting device installed upstream from the appliance. The product must
be installed in locations suitable for fire-fighting and furnished with all the services (power and outlets) which the appliance requires for a correct
and safe operation. Any repairs or actions carried out on any systems, components or internal parts of the appliance, or on any of the
accessories supplied with it, that are not specifically authorised by Thermorossi s.p.a, will automatically void the warranty and the manufacturer's
responsibility, pursuant to D.P.R. 224 of 24/05/1988, art. 6/b . Use only original Thermorossi spare parts. If the appliance is sold or transferred to
another user ensure that the guide is handed over with it.

Thermorossi S.p.A. maintains the author’s rights on these service instructions.

The information in this booklet may not be reproduced or given to third parties or used for competitive purposes without the

appropriate authorization.

1.2 SAFETY GUIDELINES

1.2 SAFETY GUIDELINES

1.2 SAFETY GUIDELINES

1.2 SAFETY GUIDELINES

1.2 SAFETY GUIDELINES

PERSONAL INJURY

This safety symbol identifies important messages throughout the manual. Read the information marked by this symbol carefully
as non-observance of this message can cause serious injury to persons using the heater.

DAMAGE TO PROPERTY

This safety symbol identifies messages or instructions that are fundamental for the heater and system to function well. To avoid
serious damage to the heater adhere strictly to these instructions.

INFORMATION

This symbol indicates important instructions for good functioning of the heater. If this information is not correctly observed, the
performance of the heater and/or system will not be satisfactory.

1.4

1.4

1.4

1.4

1.4

TRANSPOR

TRANSPOR

TRANSPOR

TRANSPOR

TRANSPORT

T

T

T

TA

A

A

A

ATION 

TION 

TION 

TION 

TION AND ST

AND ST

AND ST

AND ST

AND STORA

ORA

ORA

ORA

ORAGE

GE

GE

GE

GE

TRANSPORTATION AND HANDLING
The heater body must always be in a vertical position when handled and exclusively by means of trolleys. Take special care to protect the
electric panel, the glass, the ceramics and all the fragile parts from mechanical impact which could damage them and their correct
functioning.
STORAGE
The heater must be stored in a humid-free environment and sheltered from the weather; do not place the heater directly on the floor. The
Company denies all responsibility for damage caused to wood floors or floors made from any other material.

It is inadvisable to store the heater for long periods of time.

1.3

1.3

1.3

1.3

1.3

ST

ST

ST

ST

STAND

AND

AND

AND

ANDARDS 

ARDS 

ARDS 

ARDS 

ARDS AND RECOMMEND

AND RECOMMEND

AND RECOMMEND

AND RECOMMEND

AND RECOMMENDA

A

A

A

ATIONS

TIONS

TIONS

TIONS

TIONS

NORMATIVE REFERENCES :national and international standards used as reference guides in the following manual for the design, industrialization

        and production of the products:

- European directive 73/23/EEC

   - Standard CEI 61/50                                      - European directive 93/68/EEC

- Standard CEI EN 60204                                   - European directive 89/336/EEC

               - Standard CEI 64-8 (IEC 364)

- European directive EN 14785: 2006

RECOMMENDATIONS
Before using the appliance, carefully read every section of this instruction manual as knowledge of the information and the regulations contained
in it are essential for a correct use of the appliance.
The entire operation concerning the connection of the electric panel must be carried out by expert personnel; no responsibility will be accepted
for damages, even to third parties, if the instructions for installation, use and maintenance of the appliance are not followed scrupulously.
Modifications made to the appliance by the user or on his behalf, must be considered to be under his complete responsibility. The user is
responsible for all the operations required for the installation and maintenance of the appliance before and during its use.
GENERAL WARNINGS
Caution:  the appliance must be connected to a system provided with a PE conductor (in compliance with the specifications of 73/23/EEC, 93/
98/EEC, concerning low voltage equipment). Before installing the appliance check the efficiency of the earth circuit of the power supply system.
Caution: the power supply line must have a section which is suitable for the power of the equipment. The cable section must in any case be no
less than 1.5 mm

2

. The appliance requires a power supply of 220-240 V and 50 Hz. Voltage variations 10% above the nominal value can cause

irregular operation or damage to the electrical device. Position the appliance so that the electric power plug is easily accessible. Voltage
variations less than 10% of the nominal value can cause lighting and use problems.
Apply a current regulator. Ensure that a suitable differential switch is installed upstream from the equipment.

Содержание ecotherm 3001




































Отзывы: