Thermo Technologies USDT 3002 Скачать руководство пользователя страница 16

Страница: 16 / 16

USDT 3002

us.ind

Distributed by:

Please note:

The design and speciﬁcations are subject to change without notice.
The illustrations may differ from original product.

Thermo Technologies

5560 Sterrett Place
Suite 115
Columbia, MD 21044
Tel.: (410) 997-0779
Fax: (410) 997-0778
www.thermomax.com
[email protected]

6. Accessories

Overvoltage protection

We highly recommend installing the overvoltage protection
in order to avoid damages at the collector (e.g. by lighte-
ning).

Sensors

Our product range includes high-precision temperature
sensors, ﬂatscrew sensors, ambient temperature sensors,
indoor temperature sensors, cylindrical clip-on sensors
and irradiation sensors, also to be used as full sensors with
sensor pocket.

Flowmeter

For calculating energy gains and losses by measuring the
volume ﬂow in your system.

Содержание USDT 3002

















Результаты поиска

Содержание USDT 3002

Отзывы:

Похожие инструкции для USDT 3002

Бренды по названию

Популярные бренды

Thermo Technologies USDT 3002, Монтаж, Подключение, Эксплуатация, Устранение неисправностей.

Результаты поиска

Содержание USDT 3002

Отзывы:

Похожие инструкции для USDT 3002

Бренды по названию

Популярные бренды