Thermo Scientific RC 3BP Plus Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 70

background image

3

Control Panel

Primary Functions

3-4

Sorvall RC 3BP Plus

Thermo Scientific

Press the

key to view and select programmed parameters.

Press the

/

or

key to control the actual run.

•

After pressing the

key the run display begins to count down from the preselected value (in

minutes and seconds). The centrifuge decelerates when the timer reaches zero.

•

After pressing the

key the centrifuge will operate until you stop the run by hand. Press the

key to do so. The run display will accumulate up to 99 minutes 59 seconds.

•

When pressing the

key the centrifuge will accumulate ACE value (Accumulated Centrifugal

Effect™) and display it in the run display. The centrifuge decelerates when the specified ACE value
is reached. The run display accumulates the ACE value until the centrifuge reached standstill.

Primary Functions

ROTOR

•

Press the

key to select a different rotor. The available rotors are listed one after the other in the

set display. This is necessary if the rotor or bucket/carrier system are changed. The correct
identification of the installed rotor is necessary for the set speed litmits, correctly calculate RCF,
and accurately control sample temperature. If a rotor is able to use buckets/carriers with different
maximum radii, each configuration will be listed for selection, to calculate the different RCF.

•

The

key is not active when a run is in progress.

SPEED

•

Press the

key to specify a different rotor speed (rpm) or RCF.

•

Speed is selectable from 300 to 4700 rpm depending on the specified rotor. The equivalent RCF
value is calculated at the maximum radius of the specified rotor. Adapters are not accounted for.

•

Press the

key repeatedly to toggle between rpm and RCF. Pressing once causes the value to flash

so a change can be made in that mode. Pressing again changes to the other mode and displays a
value equivalent to the previous. Pressing the

key again causes the value to flash so a change can

be made in that mode. When pressing again the set display toggles between rpm and RCF. An
entered value will continue to flash in the set dispaly when it is out of range.

•

The formula used to calculate RCF is:

CAUTION

Make sure that you always select the correct rotor and accessories.

Note

When changing mode, rpm/RCF values may appear a digit or two off from the original set

value. The centrifuge translates set RCF values to rpm whole numbers for speed control purposes.
The whole numbers are calculated to the closest RCF value. The speed control accuracy is not
compromised, and the slight value difference will not affect your run.

RZB

11,18

Radius in cm



U/min

1000

---------------









2



=

«
...
25
26
27
28
29
...
»

Содержание RC 3BP Plus







































































Отзывы:

Нет отзывов

Похожие инструкции для RC 3BP Plus

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: Labnet Страницы: 2

Бренд: Quincy lab Страницы: 4

Бренд: Gardena Страницы: 19

Бренд: Jackco Страницы: 6

Бренд: K-9 Lights Страницы: 12

Бренд: K'Nex Education Страницы: 2

Бренд: P-Q Controls Страницы: 5

Бренд: Posture Pump Страницы: 2

Бренд: Yacht Devices Страницы: 68

Бренд: Garmin Страницы: 41

Aqua Timer 3000

Бренд: Melnor Страницы: 6

Бренд: My-Doc Страницы: 32

Бренд: Spitzer LIGHTING Страницы: 2

Бренд: Cameo Страницы: 56

Бренд: Major tech Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды