Thermo Scientific RC 3BP Plus Скачать руководство пользователя страница 22

Страница: 22 / 70

Before use

Transporting the Centrifuge

Thermo Scientific

Sorvall RC 3BP Plus

2-5

Transporting the Centrifuge

•

Use a forklift to lift the centrifuge.

•

The centrifuge can get damaged due to impact.

•

Transport the centrifuge upright and if at all possible in packaging.

Mains Connection

1. Turn off the power supply switch located on a small recessed panel in the upper right corner of the front

cabinet panel (press "0").

2. Check whether the cable complies with the safety standards of your country.

3. Make sure that the voltage and frequency correspond to the figures on the rating plate.

4. Plug the centrifuge into grounded electrical sockets only.

Other Connections

Figure 2-1.

Connetors to external devises

Note

The packaging is a one-way packaging. Assign a logistic company for the transport. Inform

the Customer Service.

WARNING

Always remove the rotor before moving the centrifuge.

15 Pol D-Sub Computer Inter-
face Connector

9 Pol D-Sub Connector Barcode
Reader

Содержание RC 3BP Plus







































































Результаты поиска

Содержание RC 3BP Plus

Отзывы:

Похожие инструкции для RC 3BP Plus

Бренды по названию

Популярные бренды

Thermo Scientific RC 3BP Plus, Инструкция по эксплуатации

Результаты поиска

Содержание RC 3BP Plus

Отзывы:

Похожие инструкции для RC 3BP Plus

Бренды по названию

Популярные бренды