Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 51

Страница: 51 / 62

Maintenance

Replacing the Temperature Controller PCB

Thermo Scientific

EASY-Spray Series Ion Source User Guide

4. Unpack the new temperature controller PCB and make sure it is not damaged.

5. Slowly push the new PCB enclosure into place, and route the heater cable so that it does

not become damaged (pinched) (

Figure 25

Figure 25.

EASY-Spray ion source (bottom) without the temperature controller PCB

6. (EASY-Spray only) Align the screw holes on the additional cover plate over the PCB’s

back two screw holes (

Figure 24

7. Using a 2.5 mm hex key, install the four hex screws into the bottom of the ion source.

You can now install the EASY-Spray Series ion source back onto the MS. To dispose of the old
PCB, see

WEEE Directive 2012/19/EU

CAUTION

To prevent damage to the electronic components on the PCB due to ESD,

hold the new controller unit by the metal enclosure instead of the PCB.

One of the back holes for
the hex screw

High voltage cable
connects to the column
holder.

Содержание EASY-Spray NG































































Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды

Thermo Scientific EASY-Spray NG, Руководство пользователя

Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды