4
ENGLISH
GENERAL
GENERAL
GENERAL SAFETY INFORMATION
b
Check that the product is complete, undamaged
and as ordered as soon as you receive it. Report any
discrepancies or damage to the
T
dealer
who sold it.
b
This product must be installed by a legally qualified
heating engineer. On completion of the installation,
the installer must issue the owner with a declaration
of conformity confirming that the installation has been
completed to the highest standards in compliance
with the instructions provided by
T
in this
instruction manual, and that it conforms to all applicable
laws and standards.
b
This product must only be used for the purpose for which
it is designed and made, as specified by
T
.
T
declines all responsibility, contractual
or other, for damage to property or injury to persons or
animals caused by improper installation, adjustment,
maintenance or use.
b
Make sure that the roof is strong enough to support the
weight of the solar water heating system under operating
conditions. Also make sure that the section of roof chosen
for the installation enjoys a high level of insolation, and
is not shaded during the day by tall plants, trees, other
houses, hills, etc..
b
The installation of a solar water heating system modifies
the existing structure of the roof. Verify the suitability of all
roof elements and if necessary adapt them to avoid leaks
or damage by wind and/or snow loads.
b
If the system is installed in an area subject to gusting
winds or snow loads in excess of the limits given in the
technical specifications, consult your supplier for advice.
b
Snow can build up in the sheltered area behind the solar
water heating system. Provide adequate protection to
avoid increasing the static load on the roof.
b
The system must be serviced at least once a year.
b
The water supply circuit must permit the storage cylinder
to be filled and emptied in safety. Shut-off valves must
therefore be easily accessible to the user and the
operation of emptying the storage cylinder must not
create any risk of flooding or other damage.
b
Insulate the domestic water pipes (hot and cold) and
the pipes of the solar collector circuit. Provide suitable
insulation for all outdoor accessories.
b
The point through which the water pipes enter the
building must be rain-proof and damp-proof.
b
If you notice any water or heat transfer liquid leaks,
disconnect the system immediately from the mains
electricity supply (if a supplementary heating element
is installed), shut off the water supply, and notify
T
’s Technical Assistance Service or a
qualified heating engineer immediately.
b
Make sure that the water-glycol mix in the solar collector
circuit is able to resist the minimum temperatures likely to
occur in the place of installation.
b
The system can reach very high temperatures. Safety
valves can therefore discharge extremely hot liquids.
Make sure that the expansion vessel is of a suitable size
and design for use in solar water heating systems.
b
Use proper slings to lift and move the elements of the
system. Never lift the collector or storage cylinder by
their fittings. Avoid subjecting the collector to impacts
or mechanical strain, and take care to protect the glass
panel. Use the personal protection equipment required
by applicable safety standards.
PRECAUTIONS
a
Never attempt to install the system without using the
personal protection equipment and without following the
safety precautions specified by applicable occupational
safety standards.
a
Never install solar collectors on roofs without an adequate
lightning protection system.
a
Never install the system without providing proper
drainage for the two safety valves: that of the domestic
hot water circuit and that of the primary (solar collector)
circuit.
a
If the storage cylinder is equipped with a supplementary
heating element, never attempt any cleaning or
maintenance without first disconnecting it from the mains
power supply.
a
Do not allow children or infirm persons to operate the
system unsupervised.
a
Do not tamper with or adjust the safety or control devices
without prior authorisation and instructions from the
manufacturer.
a
Never use anti-freeze other than that supplied by
T
to fill or top up the solar collector circuit.
Mixing different products can reduce the anti-freeze
protection provided.
a
Never drain the solar collector circuit under sunny
conditions or when the collector is hot.
a
Do not dispose of packaging material into the
environment, or leave it within the reach of children, since
it can become a potential hazard. Dispose of packaging
material in compliance with applicable legislation.
General
