thermital SUNDAY 30/130 B Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 56

background image

37

ENGLISH

INSTALLER

DRAINING

Switch the electricity supply OFF at the control panel and
at the system’s main switch before starting to drain the
boiler or storage cylinder.

DRAINING THE CENTRAL HEATING SYSTEM

- Make sure that the CH system fill cock (1) is closed.
- Close the shut-off cocks for the central heating and

domestic hot water circuits.

- Open the non-return valve (6) to facilitate draining. See

the figure to ascertain the correct position for the dot
on the screw.

- Connect a hose to the hose union on the drain cocks (3)

and (4) and open the cocks.

- Close the drain cocks (3) and (4) once the circuit is

empty

- Close the non-return valves (6). See the figure to ascer-

tain the correct position for the dot on the screw.

DRAINING THE STORAGE CYLINDER

- Close the shut-off cocks for the central heating and

domestic hot water circuits.

- Make sure that the CH system fill cock (1) is closed.
- Connect a hose to the storage cylinder drain cock (2)

and open the cock

- Close the drain cock (2) once the circuit is empty.

NOTE!
Open a hot water tap to facilitate draining of the storage
cylinder.

ON

OFF

6

3

1
2

4

OPEN

CLOSED

«
...
35
36
37
38
39
...
»

Содержание SUNDAY 30/130 B

























































Отзывы:

Нет отзывов

Похожие инструкции для SUNDAY 30/130 B

Бренд: Raypak Страницы: 74

Бренд: Hamworthy Страницы: 36

VICTRIX X12-242I

Бренд: Immergas Страницы: 40

Бренд: Kalor Страницы: 54

Vitocrossal 300 CU3A

Бренд: Viessmann Страницы: 116

Бренд: Ferroli Страницы: 28

HEATNET 3.0 Torus Series

Бренд: RBI Страницы: 136

EUTECTICEC-15DV

Бренд: Slant/Fin Страницы: 16

MicoFlame Grande MFH2000

Бренд: Camus Hydronics Страницы: 36

ecoTEC exclusive 832

Бренд: Vaillant Страницы: 56

Chef's Line CLCHRBL Series

Бренд: Eagle Group Страницы: 16

Бренд: Lamborghini Caloreclima Страницы: 96

Бренд: Buderus Страницы: 64

Logano plus GB402

Бренд: Buderus Страницы: 76

Бренд: Radijator Страницы: 58

Бренд: Radijator Страницы: 75

Ekoflux RK 34/B

Бренд: Radiant Страницы: 60

Бренд: York-Shipley Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды